Search results

  1. M

    130 v4 tach question

    Hoping someone can help me with what I need. 2001 Yamaha 130 v4 2 stroke. I installed a new old stock multi tach with the round connectors. I have a short adapter to go from round to square from the trim and oil harness. Couldn't get trim to work on gauge so I bought a separate Yamaha trim...
  2. M

    130 v4 oil tank refilling point

    I want to run my 2001 130 v4 on a 6 gallon tank of pre mix fuel before using the main tank in the boat. I placed a mark at the current level in the engine tank (after letting it fill from the on boat sub tank) I want to go through maybe 3 gal of the 6 gal tank and then lift the hood off and see...
  3. M

    Seat snap on cushion replacement

    Anyone know the brand of these seats in my 97 wellcraft 190ccf? Would like to get replacement cushions this isn't my boat in the seat picture but same seats
  4. M

    Trim guage dash question

    Looking to put a trim guage in my dash but the wood is so thick I won't have any room to put the retainer on the back. I was looking at yamaha specific trim guages and they are a lot longer. Maybe go that route?
  5. M

    2001 yamaha 130 v4 trim guage

    Trying to get my trim guage working. 2001 v4 130 2 stroke. New old stock digital tach/trim guage combo. Just getting the bottom bar lit up on guage after powering on. Got another sensor and still not reading at guage. New sensor reads 276 Ohms at 1 position then smoothly changes to 4 Ohms at...
  6. M

    Yamaha 130 run in barrel

    2001 yamaha 130 v4 2 stroke. Just installed. Idle is low. I ran it on muffs. If I run it in a barrel is that the same as running it in a lake? Just concerned with setting the idle mixture screws and idle speed before I take it out in the river. Thanks
  7. M

    Bilge sump question

    I have a 1997 wellcraft 190ccf center console. It has a sump area where the bilge pump lives. It's sealed with epoxy substance but I noticed water enters from the left side of the sump depression. Looks like its by design unless someone says otherwise. Not sure if that's intentional or if i...
  8. M

    Yamaha 130 hp idle adjust

    Just fired up new to me 2001 yamaha 130 hp 2 stroke. Rebuilt the carbs, new fuel pump, new spark plugs. I started it on the muffs at my house. Idle is low 5 to 600 rpm. I left the 4 idle mixture screws at current setting when I redid the carbs. I checked the roller cam pickup point is in spec...
  9. M

    Wellcraft 190 ccf

    I have a 1997 wellcraft 190ccf center console. In the bilge at the aft end bottom of the boat is a oval depression about 1 inch deep which is where the bilge pump sits. This area is covered with a hard waxy looking sealant. I noticed a little water in that depressed area and as I dry it up more...
  10. M

    Yamaha 130 2 stroke oil injection question

    Ready to put my 2001 130 v4 into use. It sat for a year or so. I've rebuilt the carbs and noticed the injection oil is present at the individual outlets in the intake manifold. Does thus suggest the system is ready to go? I've tested the level sensors and they work fine and also confirmed the...
  11. M

    Boat buckle tie down location

    Want to install these new boat buckles on my trailer. Not sure if either location causes an issue. Need inputs please. Thank you
  12. M

    Water separetor question

    Might be a stupid question but does the fuel water separator do a good job at filtering out particles from the boats built in fuel tank?
  13. M

    Outboard install question

    Getting ready to install a new to me yamaha 130 hp 2 stroke on my wellcraft 190ccf center console. Lower bolt holes have these thick square metal plates on the inside (ignore the thin plate with 2 screws used to hold the bolt head when tightening. Think it's OK to leave the square plates as they...
  14. M

    Vhf antenna question

    I have a new to me boat which came with a Shakespeare vhf antenna but no radio. I'm installing a uniden um385 have 2 questions. Does the end of this cable look normal? Should I be receiving communication at my house? I'm about 40 min from Salt water and 20 min from the Delaware river...
  15. M

    Yamaha v4 prop shaft carrier nut torque

    Replacing prop seals and bearing carrier o ring. Got the carrier out but wanted advice on using antiseize on the big carrier retaining nut threads. Good or bad idea? Also need the torque spec for that big retaining ring nut. Thanks 2001 yamaha 130 hp v4 2 stroke
  16. M

    Rigging preference

    Just checking which is preferred bundling the excess harness lengths at the helm under the center console or at the stern before it passes through to the outboard? Some of my harnesses have a lot of extra length. For what it's worth it's a 1997 wellcraft 190ccf with 2001 yamaha 130hp v4 2...
  17. M

    Yamaha 130 fuel connector

    Rigging a 2001 130 v4 2 stroke. Looks like yamaha wants a fuel hose from the primer all the way up to the filter with no quick disconnect coupler. Was thinking about adding one but all the Rigging coming out of the motor well is going to be inside a Rigging tube with the exception of the fuel...
  18. M

    Wellcraft 190 ccf engine install

    getting ready to install a 2001 yamaha 130 v4 2 stroke on my 190 ccf. original engine (johnson 115) was installed so that cavitation plate was about 1 inch from the bottom of the boat (boat uses a stepped transom with about 7 inches setback). Do you guys advise just mounting the yamaha so that...
  19. M

    Yamaha key switch mount horizontal

    I have to mount my key switch panel sideways for my 2001 130 v4 2 stroke due to space issues. This puts the key switch in a position that makes it look like it's on even when off. I tried rotating the switch 180 degrees but same thing. Due to the flats on the switch body and panel. Any way to...
  20. M

    Mounting bolt tab?

    Getting ready to take the johnson 115 off my 97 wellcraft 190ccf center console. Lower bolts have some kind of tab over the head of the bolts. What is the purpose of these?
Top