Search results

  1. K

    DF140 IAC Mitsubishi part number

    i just started getting the 3-1 fault code which is the IAC valve and found on another site that it is a standard part made by Mitsubishi. The problem is that on mine the tag is faded and I can not see what it is so I was wondering if anyone has the part number for this. Thanks Kevin
  2. K

    DF140 will noy always restart

    I have a 2002 DF140 which runs great. The problem is every once in awhile it will not start and the trim will not work. I was thinking that may be the main power wire but have gone thru all the connections that I could see and everything looks good. When it does do this if I pull out the ecm...
  3. K

    sportpilot steering adaptor collar

    I had to remove my autopilot to replace steering. In the process the adapter that goes from the helms 3/4" tapered shaft to the autopilot 1" taper was destroyed. Everything was seized together. I am having a hard time finding one I have emailed the manufacturer but figured someone would sell...
  4. K

    Smart Tabs on a single engine cat

    I have a 19' Seagull single engine cat and was wondering if anyone has used Smart Tabs on a similar type boat. Nauticus claims that it will improve the boat but I would like to hear from some other people. Thanks Kevin
  5. K

    225 Looper will not rev over 4000rpm

    I have a 1989 225 Johnson and it just started not getting over 4000rpm. I have checked both spark and compression and they are fine. Decided to check timing and using Joe Reeves method that the timing is at 28btdc. I tried to adjust and it does not change at all. Can the timer base go bad so...
  6. K

    1993 Yamaha VXR Pro bad carb

    New to Waverunners and we just bought two older ones for our kids. One did not start it is a 1993 Yamaha VXR Pro Waverunner. Everything else looked good on it. When I got it home the the carb had water in it and rusted up the needle seat and retaining screw. Want to get a new carb but can only...
  7. K

    Trying to figure correct prop

    I have a Wellcraft Coastal 210 with a 1989 Johnson 225, it currently has a 15x17 prop which I think is too big. At 3950 rpm I am getting 30mph.The highest rpm I can get is 5000 at WOT and am going 35mph. I pretty sure that the motor needs to be raised at least one ole maybe two but want to get...
  8. K

    New powerhead no stupid thing will not go in reverse

    Just replaced powerhead on a 1989 225 Johnson and will not go into reverse when in the water. It makes a bad grinding noise like it can not fully engage, but it goes into forward fine. I have adjusted the cable which did not help. When I checked out of water in goes in fine. I just dropped gear...
  9. K

    Where does this go

    I am replacing my 1989 225 powerhead with a 1992 powerhead and everything lines up good except the 1992 has a extra hose barb(yellow circle in picture) Does anyone know where this goes? Thanks
  10. K

    How do you remove recirculation check valves

    I just got a rebuilt powerhead to replace my 1989 225 Johnson I was told that is a 1992. I started putting everything back together and found that 4 of the recirc valves are bad. They are the kind with the screen, how do they come out? Could I also use the ones off my 89 they are all good but...
  11. K

    Broken crankshaft seal rings on 89 Looper 225

    I just pulled my 225 apart to rebuild and found that the one of the crankshaft seal rings is missing and the race is rounded over from wear. Can this be fixed or is the block junk. Thanks Kevin
  12. K

    225 Johnson thermostat question

    Just purchased a 1989 225 Johnson and had to replace a piston got everything back together and went to replace thermostat diaphragm. Pulled cover and there is a spring and no diaphragm. I have service manual it shows a diaphragm and gasket kit for the motor had diaphragms. Is this ok? Thanks
Top