Search results

  1. H

    2004 2 stroke 115 TXRD low speed miss

    I've got a low speed miss/shake, at no wake speed, about 950-1200 rpm. Just about where the butterflies start to open. 1350-1400 it smoothes out. Will the mixture screws affect operation at this speed or only with butterflies closed? New plugs, compression on all 4 120-130#, starts easy, nice...
  2. H

    Yamaha 115 TLRD carb pilot screw

    2005 two stroke, what is a good starting point for pilot screw adjustment? they seemed to be nearly closed when I disassembled carbs.
  3. H

    Mixture setting 2004 90 plsrr 2 stroke

    Any ideas as to a good starting point for mixture screw? These are the 5 point torx and the old setting was 8 turns out. It did't idle well before carb cleaning.
  4. H

    Link and sync 90 PLSRR

    Trying to do a link and sync on recently purchased 2004 90hp 2 stroke. I saw this engine start and run on hose, no sea trial. I have a factory manual, ignition analyzer on way. Starting with throttle cable adjustment, the manual is asking for an idle stop to be lightly tensioned against the...
  5. H

    2004 Johnson 90 PLSRR

    New to me engine, pulled the carbs for cleaning and found the starboard side intake manifold had a damaged check valve. You can see where the ball was bouncing against the carb base. The brass cap with the 2 small holes is missing in action. Is the new check just a press fit? Any specific cause...
  6. H

    2014 Tohatsu TDLI 90

    Looking for real-world user feedback on late model 90s, not many threads so I guess either not many sold or it's a decent motor. I'm looking to purchase one with "low hours", probably no sea trial. I will check compression, should plugs be light brown like a carb motor?
  7. H

    2001 Honda 90 shaft length?

    What shaft lengths were available in 2001? I'm guessing the one in the photo was made into a 25 with a Bay Mfg. kit?
  8. H

    1998 Yamaha 115 trim gear pump removal

    Replaced trim ram seal, and wanted to replace filters in gear pump. It separated hard because of corrosion, and a small part fell before I could see where it came from. It looks like some kind of restrictor, and its not on the exploded view. Can anyone tell me which hole it fits in...
  9. H

    1992 yam 70 hp trim problem

    My power trim/tilt was working fine. Recently I noticed that it cannot hold up trim against full throttle. You can watch the engine trim in as you apply throttle. Motor will trim up at lower speeds, tilt will hold full up all week. Fluid is full and manual release screw is full counter...
  10. H

    Yamaha 70 tilt assembly interchangeability?

    I have a 1992 70 hp 2 stroke, tilt needs help, not sure whether to rebuild or replace. Looking at different parts diagrams I see at least 3 part numbers for my TLRQ. Do the tilt assemblies interchange between years?
  11. H

    70 TLRQ control cable entrance

    I'm trying to rig a recently purchased 70 hp, I can't seem to find the parts that hold the control cables where they enter the bottom cowling. I have the plate and rubber grommet, but there must be some other part to hold the cables from moving, unless the seller gave me the wrong grommet...
  12. H

    Respirator?

    I'm looking at doing the deck on my 17 ft seaway this winter, and trying to line up what I need. What is the recommended face mask? Different cartridges for sanding and laminating? Thanks Marty D
  13. H

    2000 Nissan 90 carb 2 stroke weight?

    Looking for specs on 2 stroke 3 cylinder carb 90, is it significantly heavier than the 70 hp 3 cylinder OMC motors? Going on a 17 Seaway, with a self bailing deck, so transom weight is a concern. Thanks Marty D
  14. H

    50 hp 2 stroke 5 wire voltage regulator not charging

    90's 50 hp with a 815279- 3, 5 wire volt regulator, two yellow, two red, one grey for tach, not charging. 2 yellow wires from stator have continuity and produce 19 volts at idle, but battery terminal voltage does not rise above 12.5. Is there a way to confirm faulty regulator? New is $100...
  15. H

    1993 Mercury 50 oil alarm

    My son was on the boat yesterday, Said the alarm went off. Cooling stream is strong. Disconnected banana plug to oil tank and alarm stopped. Tank is more than half full. Am I correct when I say that the alarm only detects oil level, not flow or pump rotation? When the tank is half full I...
  16. H

    2005 Mercury Four Stroke 8 hp F8M ORO62136 No Start, Carb Back fire

    I have a no start condition on an 8hp, Motor has seen very little use, all old fuel removed, fresh gas in tank, flushed thru fuel line and pump with bulb, carb removed, disassembled and sprayed with carb cleaner, all passages clear, plugs removed, cleaned and re gapped. Still won't start...
  17. H

    1994 Mercury 50 triple tstat, 120 or 143

    I see 2 tstats listed for my 1994 mercury 2 stroke, 120 and 143 degree, which one should I use? thanks MartyD
  18. H

    WME 26 float needles

    Got Quicksilver rebuild kit for 50 hp merc carbs, New float needles are all metal, old ones have rubber tips. Hesitant to use metal needles because seats don't look replaceable. Has any problems with metal needles not closing tightly or ruining brass seats ? Thanks MartyD
  19. H

    50 hp 2001 2 stroke Johnson

    I'm looking at a 2001 Johnson 2 cylinder 50 ,to replace a Yamaha 3 cylinder. Is there a big difference in torque or smoothness? Is 2001 OMC or Bombardier? Do they have a good reputation? Thanks Marty D
  20. H

    1986 Suzuki DT 55, surging, down on power

    Suzuki DT 55 compression 140 +or - 5, good cranking spark, 10 micron racor, no dirt, no water. Hole shot getting worse, seems to surge at mid range. Plugs were nice and even brown at the begining of the season, all three different now. I think I need to pull the carbs, what problems should...
Top