My setup is a dual station, single engine 200hpdi (2001) with the second station on the upper helm, on a 22v Pathfinder.
The lower station has the normal keyed ingnition/start switch and the upper has pushbutton on/off switches. For the engine to be started at the upper station, the lower...
I really could use some help removing the plastic, felt covered part that covers the coil wires as they route to the plugs. After removing the felt and then the 2 tabs covering open slots, I can find no screws that I anticipated that would release it........I need to remove it to get to the 4th...
The engine is a 2001 200hpdi and there is already a water gauge at the console, and it works fine. I have bought a 2nd gauge for the tower station but I could use some help installing it.
Anyone know where I can acquire the clear plastic tubing (it looks to be about 1/8th inch....maybe a...
I have an LCX-15mt on my lower station but recently bought an X47 for my upper helm (22ft Pathfinder with upper helm station on tower). I don't know if there is an adapter so I can use both finders on the same transducer.........anybody have knowledge of this?
If not, I'm going to have to fish...
I'm about to install a water pump kit in my 200hpdi and it will be my first time (I used to do it on my last motor - a 90hp Merc).
Who uses what to support the gearcase while doing the work? Is it best to have it in the upright position? I was thinking of something like a couple of 2x4's...
I recently finished the installation of a helm tower on my Pathfinder with a (year 2001) 200hpdi and I used the wiring bundle from one half of a Yami dual engine installation. Everything works great with one exception:
Both tach's are giving me some incorrect info. The RPM reading is good but...
I unscrewed my Shakespeare 4400 from the mounting base and unwittingly broke it.......it appears that the coaxial cable just pulled out as I unscrewed. I haven't been able to take the antenna apart to see how the cable was fitted inside. Are these things repairable? Anyone know how to get it...
I'm installing a tower on my 22ft Pathfinder and have four deck plates on the unit. The forward plates are over aluminum below-deck plates and will be drilled and tapped. The rear plates will be afixed to the deck only - with screws and adheisive (no below-deck plates).
Should I use 3M 5200...
I'm planning on replacing the Yamaha fuel/water seperator filter on my boat but I don't know if I can just re-use it after dumping out any water, rather than replacing it (it's about one year old). Is that advisable? Thanks!
When I bought my boat 3 months ago it had, and still has, the Panther 300 Jackplate on it. The motor on it has the only rust (it's on the motor housing only) or corrosion on the entire boat/engine and I'm concerned that it will rust through and destroy the motor......so I'm hoping I can hear...
A friend's 90 FICHT will run at advanced rpm's but dies when it is taken down to idle. We've checked for any obvious problems like loose electrical connections or a leak in the fuel line, and none seem to exist. We also couldn't find an idle adjustment so I'm assuming that that's controled by...
It seems that the rectifier/regulator is not functioning on my 2110 200hpdi....the reading across the starting batt at all rpm's never goes above 12 volts. Anyway, I can get through a day of fishing with one fully charged battery, and a couple times I had to switch to the backup battery. My...
On my 2001 Yamaha 200hpdi it appears that I'm not getting any power back to the main marine starting battery. I just tested the voltage across the battery with the motor running from idle to about 1700rpm and the reading never went over 12 volts.
Can some of you seasoned guys tell me where to...
Yesterday I had to troll the entire width of Tampa Bay to get back to the dock after I lost battery power to my engine and accessories. The battery reads 12.08 volts and was connected properly - not loose and no rust or corrosion problems. I didn't even have power to the tilt trim on the 200...
This is a 2001 year 200hpdi with low hours but the main switch (the one on the console with the key) started sticking last week. I turn it on, then to start, and it wants to not return to the on position without encouragement.....in other words, I have to slightly turn it back counter-clockwise...
