Recent content by StingrayMike

  1. StingrayMike

    Need to flush-boating in freshwater? and where to do it??

    Just moved to CO, now boating in freshwater only, vice salt. I tried to find any posts, but could not. Since now I am in freshwater, do I need to flush after every use? The 2nd part is where? I keep the boat stored at a storage facility with no access to water. I don't the room where I live to...
  2. StingrayMike

    Will I need to winterize in Colorado Springs?

    20015 Stingray bowrider Yamaha F250 OB Most definitely will be making the move from Fl to Colorado Springs. Been out there a few times to check things out and look how the boating will be, Not Fl ocean, but still some good choices. Looking in the Colorado Springs / Manitou Springs areas...
  3. StingrayMike

    Colorado boaters??

    Currently in South Florida but most likely moving to Colorado Springs area next year. The question I am asking is how is the overall boating community? Down here it seams like 80% of the boaters don't care about other boaters, navigation rules ,and general boat safety. I would assume most don't...
  4. StingrayMike

    Do I need to replace steering hose?

    2015 Stingray with F250 Yamaha, uflex manual steering (no hyd pump) I noticed that the hose that connects to the right fitting ( if looking at it from the from) is crimped over alittle bit. Should I replace it? I do not have any issues steering,so I believe the integrity of the cable is good...
  5. StingrayMike

    Transducer Cable Clamps for Transom

    You can get some clamps from almost any marine store or do it yourself store. something like this works just fine. You need to predrill the holes, countersink the gel coat so it doesn't split and seal with silicone.
  6. StingrayMike

    Yamaha F250 trim position not working properly on N2k network

    I just hooked up my Yamaha F250 to my N2k backbone to a Garmin. All engine data is correct, with the exception of the trim position. it is WAY OFF. ​The analog gauge is working fine. ​I did connect the 2 pink wires at the engine, before I did that, it was not displaying on the Garmin. ​I did not...
  7. StingrayMike

    Factory installed voltage sensor relay?

    Mine has both positives from the VSR going to only 1 battery. here is a pic
  8. StingrayMike

    Factory installed voltage sensor relay?

    2015 stingray 234lr yamaha f250 dual batteries I have had the boat for a few months and I want to install a dock battery charger. I went to install it and was checking out the wiring and I am confused???? Both leads coming from the VSR are going to only 1 battery. Shouldnt a lead go to each...
  9. StingrayMike

    Tower Speaker wiring - thru the hull pics??

    Not sure of your cable size, but when I do cable runs that penetrate the hull to a external component, I use perco fittings
  10. StingrayMike

    will be upgrading to different style of boat. Biggest surprise you encountered?

    Currently have a 21' deck boat and will be getting a 26-28' cruiser. I know there will be big differences in the 2, but for anyone that made the leap, what some things that you didn't anticipate? I will be using the boat for overnight/ weekend trips, so generator is a must. my marina can...
  11. StingrayMike

    wifi camera to monitor boat at dock

    I am looking to get a simple 1 camera wireless camera system to watch the boat, mainly during storms and high winds. I work with higher systems, but the monthly cost will eventually overcome the one time cost. what is anyone using or seen out there? thanks
  12. StingrayMike

    where to get helm gauge panel blank

    I am looking to flush mount a chart plotter into my helm panel and looking for a helm panel "blank". Just the panel without the holes cut in for the gauges. the finish is the gnarled wood grain, so would like to keep that theme going. Are there any companies out there that does this? I been...
  13. StingrayMike

    Could enginge alignment be that far off?

    VP 5.0 GXI-F w/SX-M 1.66 outdrive I had to pull the engine to replace the inner transom plate, so after I put the engine back in, I checked the alignment. The tool would go in, but was very difficult. There was defently spline marks on the top, and very little on the bottom. I adjusted the front...
  14. StingrayMike

    Broken Transom mounting plate tab for steering cylinder.

    2006 Caravelle 218 LS Deck boat 5.0 GXI SX-M Outdrive Long story short was re-installing my steering cylinder after replacing an o-ring and the lower tab that hold the cylinder to the transom bracket broke. Don't know how, well I do, but never felt/had any warnings. So I think my options are: 1...
  15. StingrayMike

    ICOM OPC-980 clone cable adapter

    Seems right. This is a pic of the program that I use. for the actual cable, I cut off the 3.5mm jack on the adapter and solder the lead that was to the center to pin 8 on the cmd mic plug(green) and the lead that was going to the sleeve(bottom) to pin 4 (blue) on the cmd mic plug. the tip of the...
Top