Recent content by Fabreezai

  1. F

    1963 Mercury 350

    Thanks again guys. Here is what I think is going on from what I found. #67 (what im calling thin splined washer) goes on first, then the thrust bearing (#68) and lipped washer(#69), then prop, then crown washer, then lock nut. the key is the splined washer that goes on first, bottoms out on...
  2. F

    1963 Mercury 350

    Ah, found this doing some searching. you're talking about #68 in pic. on the hunt for that now. thank all of you for all your input!
  3. F

    1963 Mercury 350

    would this be the thrust bearing? if so, seems to be stuck in the back of the prop.
  4. F

    1963 Mercury 350

    Thanks for replies! I guess now, my question is: Is the thin splined washer the thrust washer that should go on first so it bottoms out on splines, then prop, then thick splined washer, locking tab (missing from the get go), then lock nut?
  5. F

    1963 Mercury 350

    Hi guys/gals- Rescued this engine from FB, guy said he could not get it to run. just looking for some conformation. I took the lower unit off, to replace water pump as a standard practice, and was going to replace seals as well. when I removed the prop it came off in the order shown, lock nut...
  6. F

    the ever elusive alpha 1 gen 1 service manual…..

    Bt- thank you so much! was able to locate one in no time 😎🍻
  7. F

    the ever elusive alpha 1 gen 1 service manual…..

    Hi guy/gals- looking to change bellows, cable, etc. on the hunt for a pdf service manual for our searay CC out drive. it has the alpha 1 gen 1 drive. i think its manual 6 opposed to 14. can anyone enlighten me to a link or web location for it? been looking for a couple hours and cant seem to...
  8. F

    1989 Sea Ray CC moulding

    looks about right, just tried a small piece.
  9. F

    1989 Sea Ray CC moulding

    have not had a chance to try mine yet, we got a big dump of snow….. maybe over weekend.
  10. F

    89’ searay 200 cuddy cabin

    thanks guys- Will do! will have to get pics and repost! that is at the top of my list now! 🍻🍻
  11. F

    89’ searay 200 cuddy cabin

    judging from the pic I think you are right! Guess I never thought about it 🤦‍♂️. I have new seats to install in it, so I guess Ill have to address this issue prior. par for the course I guess. no wonder its painted with that “sand” textured paint. 🤷‍♂️
  12. F

    89’ searay 200 cuddy cabin

    Ill have to look 👀 into that deeper then. the Boat is covered in snow right now (live in CO). so it will be a bit before I can work on it. come to think of it…. last summer, working on it, I vaguely remember a corner joint looking “different” when working in the cabin. I think I have a picture……...
  13. F

    89’ searay 200 cuddy cabin

    thanks Scott, I doubt it was decked over, prior to me someone did a HACK job “fixing up” the boat. Guess I should have said, I rescued this boat. everything they did (so far) I had to tear out and redo. the decking material is about the only thing that was worth keeping. to sum it up, I have a...
  14. F

    1989 Sea Ray CC moulding

    I ordered the Taco v12-0334bka50-1, should know later today (if it arrives on time) if it fits. It looked and measured just like my old petrified rub rail. Ill repost with results if you would like?
  15. F

    89’ searay 200 cuddy cabin

    Hello guys/gals- We have a 89 200 cuddy, we purchased it late last summer, a prior owner removed the carpet from the floor and replaced it with some of that “teak” stick on decking. can someone confirm for me that there is storage under the floor just forward of the fuel tank? It does show one...
See more
Top