Search results

  1. garbageguy

    Decarbonizaton

    Definitions. For our internal combustion engines, decarbonization means something different than what some think now, looking for info on this today yields... "Decarbonization (also decarbonisation) is the process of significantly reducing or eliminating carbon dioxide (CO2) and other...
  2. garbageguy

    wood handle preservative question

    What do you recommend using to protect the wood handles on this (photo) new to me, lightly used wheelbarrow? I'm thinking some kind of oil w cleaner. I'm only looking for it to be a worker up at camp, not pretty.
  3. garbageguy

    Seat cushion for small aluminum boat?

    Looking for suggestions on seat cushions for a 14 ft aluminum boat with small side driver console. (Alumacraft w 20 HP outboard). It's our 2 mile by 4 mile Adirondack lake camp fishing boat Our current method is to sit on a throwable cushion, towel, whatever. I envision two cushions (one for...
  4. garbageguy

    small cruiser aft seat repair?

    The aft seat bottom cushion backing (wood?) is shot. Can't get to it in-place so I'm assuming the entire aft-seat will have to be removed to do that. 2 questions (to start). Any other ideas on how to replace that bottom "backer-board" other than removing the whole thing and doing the repair...
  5. garbageguy

    Hidden horn diagnoses

    The little electric "hidden horn" on 1998 Wellcraft 240SE was weak when I got the boat about 7 yrs ago. Since last yr, no sound at all. Assuming the little horn reached end-of-life, bought a replacement Attwood horn for about $10. Before removing old horn, pulled wires, getting 12-volts...
  6. garbageguy

    Trim tabs not operational

    1998 Wellcraft 240 SE with carb'd 350 reman long block about 2 yrs ago and VP Cobra SX and merc ignition parts (a bit Franken-ish). Runs great, had someone else throw in a new dash-mounted ignition switch when they put batteries in and launched it a few weeks ago (did not have time myself). That...
  7. garbageguy

    Toggle ignition switch?

    1998 Wellcraft 240 SE with repower 5.7 liter GM normally aspirated. VP Cobra outdrive, I think Merc electronics on the engine. Got it used, replaced 5.7 with long block 2-3 years ago (frankenmotor?). It runs very well, but the keyed ignition switch plastic broke. I am able to start/run by...
  8. garbageguy

    Grand Island NY to Crystal Beach Ontario

    How long does it take and what is the way to go by boat from Grand Island, NY to Crystal Beach Ontario? Actually starting at south GI bridges 25 ft small cruiser just up on plane. Wind is forecast to be about 5 mph.
  9. garbageguy

    Those great Winnebago runabouts

    Since they're buying Chris-Craft, does everything get new nameplates?
  10. garbageguy

    Fresh water pump?

    24 ft cruiser fresh water system. Pump builds intermittent pressure, plumbing is good, suspect it's the little diaphragm pump. Agree? Other things to consider? Source for replacement pump? Pump-replacing tips? pump close-up
  11. garbageguy

    Suggestions on bottom paint?

    What bottom paint do you recommend for 1998 Wellcraft 240 SE? The green stuff on their is like some kind of ablative that was on there when I got it about 5 yrs ago. It is slipped seasonally in fresh water, otherwise stored on trailer. I'd like to re-do the bottom paint when it comes out of...
  12. garbageguy

    Keep 09 Malibu or 06 Silverado?

    Looking for input from the good folks here My 26 yr old son is getting a new Tundra (must be nice). We need to trim the fleet, but keep our daughter in a vehicle for a few years - she's a freshman at local university. Should we get rid of an 09 Malibu with about 90k mi on it, or an 06...
  13. garbageguy

    oil filter wrench suggestions?

    We're looking to get a new oil filter wrench - suggestions on what/where to get? 1998 Wellcraft 240 SE, 25 ft small cruiser. GM 350 ci, carb'd (VP outdrive)
  14. garbageguy

    Layup storage outdrive position

    My small I/O cruiser (24 ft Wellcraft 240 SE with carb'd 350 engine and VP SX-M outdrive) is stored over the winter by my marina. We pull it, put in the the trailer, winterize it, then leave it on the trailer at the marina. They take it from there. So, the outdrive gets left in the up...
  15. garbageguy

    Anchor/rode/line suggestions?

    My anchor now sits at the bottom of Lake Erie. I was a good Danforth with about 4 ft of chain and about 200 ft of 3/8" anchor liine. For use on a 1998 Wellcraft 240 SE, what do you suggest as a replacement and from where? We usually are on Upper Niagara River ans western basin of Lake Erie...
  16. garbageguy

    59 Century Coronado

    My son's friend is great with old boats, cars, etc. There are kids out there that enjoy the old-school. Thought you might enjoy his latest endeavor, he put it in the water for the first time this weekend - glad I was there (finally) to enjoy it!
  17. garbageguy

    What do you think of this Formula

    Good friend of mine looking at this boat http://www.boattrader.com/listing/19...sport-99434936 what do you think of it? Anything specific we should look for?
  18. garbageguy

    NY Registration sticker faded

    It's good through 2018, but the sticker on one side is completely faded - anyone know what, if anything I have to do. I passed a LEO last night expecting to get stopped, but wasn't. So it's got me thinking, and wonder what the good folks here think. What's the law say? What do you think I...
  19. garbageguy

    Looking for boat cover support pole end caps

    The bottom and top (with snap rubber end caps have seen better days. Anybody know where I can buy new ones?
  20. garbageguy

    VP SX-M trim cyylinder

    I have been told that one of my drive trim cylinders was "puking milky oil", must be replaced, cannot be rebuilt, and a new one is $589. The drive is on a 1998 small cruiser, and is the original drive as far as I know. Does this sound right?
Top