Search results

  1. eggs712

    My 84 4winns horizon 195 project.

    The styrene fumes are nasty; it makes me feel hungover the next day if I get too much exposure. I bought some organic vapor cartridges since my cabin boat is has poor ventilation, it does help a lot.
  2. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I'm using white FRP for the headliner with 1/2" foam and reflectix underneath. I'll secure the FRP with 1/4" varnished cedar planks using SS screws and finishing washers. For the ceiling lights I've already installed, I bought some nylon standoffs/spacers to make them flush mount; I kinda wish...
  3. eggs712

    Re-powering a 1978 21' Starcraft Mariner - Engine Help!

    Maybe stick some newer decals on your motor?
  4. eggs712

    1985 pro craft 1750v

    My '83 1750V had a half-inch deck.
  5. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I'm hoping by the end of this summer.
  6. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Saturday, I used vapor barrier to make templates for the V-berth and dinette cushions: My Singer 15-91 has been rewired, gears re-greased, new brushes installed in the motor, and thoroughly oiled. It appears to be running great, so I can hopefully start learning to sew on weeknights while...
  7. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    The keystone cushion wood warped a lot (2.5" bow) after sitting a week. I don't have access to a steamer, so I experimented. I soaked the concave side of the bowed piece with antifreeze and weighed it down with buckets of water for six hours. This actually worked in fixing the bow, so I added a...
  8. eggs712

    Bent Transom

    Aluminum is very prone to work/strain hardening, so bending it back may do more harm than good. The correct fix would be to replace the damaged section of aluminum. If you want to risk fixing it, I would pull the motor, and use either a porta power or a comealong setup to carefully pull it back.
  9. eggs712

    My 84 4winns horizon 195 project.

    I like to use PL whenever the temperature window for poly resin isn't right, but having a heated shop would negate that.
  10. eggs712

    Bought my first boat to tinker on. Looking for advice

    It sounds like a Teleflex steering system, pretty ubiquitous on older boats. I would spray some fogging oil in the cylinders and worry about it next year.
  11. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Still plugging away here, but the weather has not cooperated on the weekends. I wasted a lot of hours trying to remove all the old carpet glue in the cabin, which I'd been putting off. The only thing that finally worked was a wire wheel in my drill. Still slow and messy, but most of it is gone...
  12. eggs712

    1985 Beachcraft Cuddy Model 240C rehab

    Wild. I know some off-the-wall ideas float around here sometimes, but concrete stringers in a little glass boat is pretty special.
  13. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Hot compression numbers are: 8: 148 7: 156 6: 130 5: 148 4: 130 3: 145 2: 150 1: 154 I'm not sure if cylinders 6 & 4 are bad enough to reevaluate keeping this motor.
  14. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    The engine not cranking was only the relay before the starter solenoid having gone out. I was able to start and run the engine for 30 minutes tonight, and the cooling system and everything else seems in good order. I'll get warm compression numbers tomorrow.
  15. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I wish I'd done it much sooner.
  16. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I added a GT51 transducer for the new fishfinder, and used a Blue Sea Systems horizontal cable gland to run the cable through the transom. I think it gives a clean look: I also added a bronze high speed water pickup with a proper seacock and dual outlet aerator pump: I plumbed a washdown...
  17. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I finally received the Sierra risers for the engine a few days ago. Those were installed with new exhaust hose today. I was ready to start it, but the turning the key didn't engage the starter. I may have messed up a wire during all my electrical tinkering; I'll track that down next weekend...
  18. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I'm slow at this electrical thing... lots of random wires and poor splices have been cleaned up though. Also: -Emergency bilge pump (3700 GPH) and new thru-hull is installed. -High water alarm that beeps and flashes at me is installed. -I'd bought Seaflo electrical sensor waters, but one didn't...
  19. eggs712

    New project.

    I'd take it all out and start fresh.
  20. eggs712

    New project.

    Accidental post
Top