Search results

  1. C

    Adding electric start to a 96 Mariner 30hp

    Makes a lot of sense, thanks for the quick reply
  2. C

    Adding electric start to a 96 Mariner 30hp

    Hi Newbie here, adding electric start to a 30 hp outboard. I've included electrical diagram I'm using . Wiring in the existing stop switch (from the tiller handle) and adding a kill switch seemed pretty straight forward (black to black, black/yellow to black yellow leads already prewired on the...
  3. C

    Swapping Short and Long Shafts between outboards

    I checked and compared the parts list, gear housings looks different in diagrams and driveshafts are different part numbers. Do you still think as long as the splines are the same it would work?
  4. C

    Swapping Short and Long Shafts between outboards

    I would like to know if it is possible to swap the lower units between a Mariner 30hp short shaft (serial#0G193173) with a Mariner Magnum 40hp (0G137689) both seem to be in the same time bracket. I understand that the mounting bracket is different since the 40hp has tilt trim. Thanks
  5. C

    Achilles floor replacement

    Can you give me a play by play on what you did (pictures)?
  6. C

    Achilles floor replacement

    Hi everyone, I have a used Achilles 14 with badly deteriorated plywood floor sections. I would like to separate the aluminum extrusions/frames from the old plywood but looks as though the plywood was press fit into the extrusions (and probably some wood swelling as well). Is there any trick to...
  7. C

    Achilles plywood floor replacement help

  8. C

    Achilles plywood floor replacement help

    Hi everyone, I have a used Achilles 14 with badly deteriorated plywood floor sections. I would like to separate the aluminum extrusions/frames from the old plywood but looks as though the plywood was press fit into the extrusions (and probably some wood swelling as well). Is there any trick to...
  9. C

    reusing the aluminum extrusions from floor boards

    Hi everyone, I have a used Achilles 14 with badly deteriorated plywood floor sections. I would like to separate the aluminum extrusions/frames from the old plywood but looks as though the plywood was press fit into the extrusions (and probably some wood swelling as well). Is there any trick to...
  10. C

    Rubber seal around pull start for Nissan NSF30A Cowling

    I cannot find this seal in the parts manual, does anyone have a source for this part, new or used. I've enclosed an image ..thanks
  11. C

    Switching 25hp Nissan electric start/charging over to a 30hp Nissan

    Hi, I just bought a 2002 Nissan NSF 30hp with manual start, I also have a 2002 Nissan NSF 25hp with both manual and electric start. I would like to switch over the electric system from the 25 to the 30 and sell the 25hp as a manual start. Is this in the realm of a do it yourself mechanic. Is it...
  12. C

    Nissan NSF 2002 25 hp No water out the pee hole

    I went to start up my Nissan outboard today and no water is exiting the pee hole, just warm air. (The prop and intake were fully submersed in a large bucket) Pulled off the thermostat and it's bone dry inside no clogging. Is it the impeller? Motor has about 60 hrs on it tops. Always operated in...
  13. C

    Nissan NSF 2002 25 hp No water out the pee hole

    I went to start up my Nissan outboard tofay and no water is exiting the pee hole, just warm air. (The prop and intake were fully submersed in a large bucket) Pulled off the thermostat and it's bone dry inside no clogging. Is it the impeller? Motor has about 60 hrs on it tops. Always operated in...
  14. C

    Hi Urgent Nissan Motor repair

    I'm located in London Ontario. I have a Nissan 25hp four stroke NSFA 2003 serial # 030776XC. I noticed a hose connector broke off on the vacuum?? section of the top carb (see picture) and the motor has been slamming into gear. I'm in a bind to repair this and the closest Nissan dealer is a...
Top