Search results

  1. U

    Trim tabs stopped working.....help!!

    Our boat is a '97 pursuit Denali 2460 and the trim tabs stopped working. Does anyone happen to have a wiring diagram for them? I'm sure it's just a relay but I don't know where to look. The fluid reservoir has the correct amount of fluid. Thanks!
  2. U

    2460 Pursuit Denali

    The side vent on the starboard side of the boat fell out on the way back from the keys last week. After speaking with Pursuit and the company that manufactured the window, it looks like I'm left to scouring the web for one. Does anyone know know where I could find one? Thanks
  3. U

    DP-SM Bearing Carrier Install....HELP!!

    HELP!!!!! I am in the process of rebuilding my '97 VP DP-SM outdrive and I cannot get the new bearing carrier to go in. Does it need to be pressed in, in a press? Does it get pressed in using the inner prop shaft? It needs to go a good 1/2" before I can even start the retainer ring.
  4. U

    How far would you go??

    So after I got the lower unit off of my VP DPSM outdrive, I found metal shavings inside the connector that connects the LU shaft to the mid section shaft. I also found them on the bearing under the dip stick cover. Would you do a complete tear down to find where its coming from or would you...
  5. U

    Volvo DP-SM carrier bearing removal

    I am a pretty proficient DIY'er but I have some concerns that I'm about to enter the dark side w/o the tools or knowledge to get back over... I need to replace the carrier bearing housing in my outdrive b/c (wellll don't ask). You can see in the picture that it is missing a piece. This is on...
  6. U

    Evinrude WOT issues??

    I have a '89 40hp Evinrude outboard on the back of a 1648 mod v jon boat. It cranks fine, runs great through 70% throttle and then it starts to sound like its missing. If I am on really smooth water, the engine will open all the way up and I will pick up about 10mph. Whats strange is that its...
  7. U

    Faria Tilt/Trim Gauge working backwards

    Engine - '89 Evinrude 40hp I just installed a new tilt/trim gauge, which I purchased from ebay. Its a Faria Euro tilt/trim(omc evinrude). I have a wire coming from the tilt/trim unit, which I thought was the signal wire, I have an ignition wire from the control box and a ground wire. When I...
  8. U

    40hp Cranking Issue

    I have a 1648 fisher and decided to move my batteries to the front of the boat. To get the power back to the outboard, I ran 4 gauge power and ground wire from front to back. When I crank the engine, it will act like the battery is dead (for just a second) then it will spin then crank. I have...
  9. U

    Do I need this seal???

    I have taken my '88 40hp Evinrude apart and in the process of repainting all of the parts. The steering arm seal (part # 0332169) was pretty messed up, from years of oil and gas (i guess). That little seal is $94.97 :eek:.....do I need that and if so, what exactly does it do? Any help is...
  10. U

    40hp Evinrude WOT Issues

    I have had this boat/engine model# E40TLCCS for a few weeks now and here these are the symptoms of the engine. Starting/Idling - Excellent Idling - 75% throttle - Excellent 75% - 100% throttle - hit or miss. Sometimes the engine will come alive and pick up about 1500 rpm's and run like a...
  11. U

    '88 Evinrude 40 VRO

    Recently purchased an '89 fisher boat with a '88 Evinrude 40hp VRO (model# E40TLCCS) The engine cranks on the first hit, idles, takes off and runs great up until around 75% throttle. At that point, the engine starts to make a slight chattering sound. Not knowing what it was, I came home and...
  12. U

    '89 Marsh Hawk 2v Specs?

    All, I have searched until I'm blue in the face. I am looking for the specifications on my '89 Fisher Marsh Hawk 2v. It is 16' SC with a 40hp on the back. The tag that tells the hull weight and how much it can carry has been damaged over the years and its unreadable. I have called Fisher...
Top