Search results

  1. 9

    Yamaha T50 won't exceed 3500 rpm

    a t50 pushing a 20 ft pontoon? not much motor . have you looked at what other people are pushing a boat like yours with? also what prop they used? look at yamaha performance bulitens online to see if they list a T50 for a toon like yours , and if so what prop that used.
  2. 9

    Correct Sparkplug 2000 200hp Saltwaterseries 2 stroke

    That is not the Yamaha manual. do what you want
  3. 9

    Correct Sparkplug 2000 200hp Saltwaterseries 2 stroke

    was that a Yamaha service manual or an aftermarket one? Boscoe said the Yamaha service manual and owner's manual by the way you mentioned copper ring on some plugs, copper and aluminum do not get along well touching each other
  4. 9

    130 v4 oil tank refilling point

    simple to start draining the tank slowly and see when it refills but I would think your service manual for your motor would tell you about how far it would move to set the switch
  5. 9

    Yamaha 115 (2003) leaking water

    time to pull that cover off and see what the problem is
  6. 9

    Yamaha 2-stroke 50HP 1980's bogs and not reaching max RPM

    sounds like you are making headway
  7. 9

    2001 Yamaha 50hp tlrz 2 stroke with prime start system starts and dies

    sounds like a lean sneeze. and pump is not doing its job if pumping the primer bulb helps. check to make sure pump is still good, and the idle jets/passages are feeding the fuel needed for each cylinder
  8. 9

    yamaha F250 DERATE to F225

    just put the F250 on there and do not run it as hard
  9. 9

    2001 Yamaha 50hp tlrz 2 stroke with prime start system starts and dies

    hopefully you have a timing light to check this
  10. 9

    2001 Yamaha 50hp tlrz 2 stroke with prime start system starts and dies

    idle timing is After TDC, ( retarded timing) WOT timing is Before TDC.(advanced timing) guessing at what the timing is actually doing by looking at the none functional wiper does not help at all
  11. 9

    2001 Yamaha 50hp tlrz 2 stroke with prime start system starts and dies

    if timing is not close to correct with the wiper pointed at the marks, then I would say it needs replacing. what does the timing light show the timing at when wiper set to where the motor will run?
  12. 9

    2001 Yamaha 50hp tlrz 2 stroke with prime start system starts and dies

    I had to replace my CDI due to the idle timing retarded 14 Deg when set to the marks on CDI. others had jacked with all the carb linkages just to get it to idle, WOT was as problem. and it did not help that they had drilled out the main jets too. took me a long time to finally get the motor...
  13. 9

    Suzuki DF140 Fuel Water Separator

    are you saying you cannot pull the cowling off to see where the fuel line runs around on the motor?
  14. 9

    Suzuki DF140 Fuel Water Separator

    follow the fuel line going into the motor
  15. 9

    Yamaha T50 any way to increase charging/stator output ?

    charge every night or get a small generator. or solar panels. please do not disturb everyone else with your loud noise on the water, that would also be helpful with your battery drain
  16. 9

    2001 Yamaha 50hp tlrz 2 stroke with prime start system starts and dies

    low oil or over heat will set the buzzer, but neither will shut down the motor
  17. 9

    Yamaha S130TXR8.1996 Identification.

    the motors were designed to have them in place, so I would put them back. there are check valves and just plain nipples on those. good luck knowing how they are routed. hopefully your manual shows that
  18. 9

    Yamaha S130TXR8.1996 Identification.

    I guess puddling hoses are the recirculation hoses tied into the crankcases and manifolds to clear out the liquid in crankcase
  19. 9

    Yamaha S130TXR8.1996 Identification.

    My guess it is a S130TXRU if it really is a 1996. what the heck are puddling hoses there should be a round decal on the block next to starter with some numbers/letters to help ID it
  20. 9

    2001 yamaha 130 v4 trim guage

    find the manual for your gauge and read up on how to set it. probably some dip switches
Top