Current visitors

Home
Members

Noah4200's latest activity

N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

It worked!!! It was the CDI. I know they are robust but i think my old delaminated flywheel magnets hitting sent nasty waveforms and...

Apr 20, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

Ok it’s ready for a sea trial. One last thing i’ll mention that gives me GREAT hope is that today i did a cylinder drop test and the...

Apr 7, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

HAVE NOT RUN THE NEW CDI YET. Hunted around all afternoon. Neither shorting the oil or temp sensor wires to ground point triggers the...

Apr 7, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

So i jumped the CDI Y/G output wire that is in charge of buzzer activation during overheat/low oil and buzzer worked. When i jump the...

Apr 7, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

so either the temp sensor input path to CDI or buzzer wire output from CDI have a problem. Bc the trim control buzzes no problem and is...

Apr 6, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

Ok i swapped the Red and yellow and grounded temp sensor and oil light went out so i think it’s the red bulb that’s malfunctioning. Now...

Apr 6, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

I checked the blue/yellow to the buzzer too. Has continuity. So the gray wire from the indicator lights that goes to the multi panel...

Apr 6, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

Thanks matt. I got it on and started in the driveway..everything sounds about the same. Will bring it to test ASAP. Just for the heck...

Apr 6, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

Even with a new high end MM i still couldn’t get nearly any of the readings to be right on either CDI and they were consistent amount...

Apr 5, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

I guess resistance at rest and room temp isn’t that valuable anyway…more about voltage output when warm under load. Just gonna swap...

Apr 5, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

Allright terrible news…the CDI that arrived shows mega ohms too. 5 mega ohms. Which is 5,000 K ohm. Specs say 5-500 K ohm. This is...

Apr 5, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

Awesome..thanks again. I just saw the top cylinder is like 165-170 in the driveway where the lowers are 145-150. Overtemp is like 195...

Apr 5, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

CDI will be here friday. Paid 250$ but got the nicest one on ebay and from a 100% seller. I put the new fuel pump on today. After...

Apr 4, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

Just for clarity…ALL my measurements on the CDI are showing 4-5 MEGA OHMS. The honda specs call for 5-500 kilo ohms. So we are out of...

Apr 2, 2024
N

Noah4200 replied to the thread 1996 BF50 Honda Bogging out when trying to plane.

I bet my the old flywheel magnet delamination contributed to the CDI failing. Sending junk pulses into the circuit with each strike...

Apr 1, 2024

Show older items

Home
Members

Top