Search results

  1. puffitu

    Suzuki DT15C wiring schematic

    I would like to know if anyone had come across a wiring schematic for this model. Can’t seem to find much info on this DT15C which has been converted from oil injection to premix. Thanks
  2. puffitu

    2004 Honda 9.9hp four stroke impeller change

    Trying to change the water pump impeller on this unit and having a hard time with the shift rod connector; after un doing the lock nut which was no problem the connecting nut will not budge and I’m afraid to muscle it. It’s really hard to see why it won’t thread up as it should. I soaked it with...
  3. puffitu

    Mercury 9.9 four stroke OHOO3349

    Hey everyone, Recently got a mercury 9.9hp 4stroke and after going through it somewhat, I got it to finally crank up but only by having the throttle wide open while pulling the cord. It will sort of run but only if I keep on the throttle; soon as I release it the motor will stall. Checked oil...
  4. puffitu

    Tilt-n-trim electrical

    Hello I have an arco marine 2wire tilt and trim unit which I’ve found to have a loose green wire coming out of the top of the pump housing. My question is; can I take off the housing to motor assembly to diagnose without draining the fluid?? Finally found issue which was on/off from time to...
  5. puffitu

    87 force 125hp high speed studder

    Hey fellas My 1987 force 125hp has developed a slight high speed studder or miss. Any ideas as to what it may be? It only does it while wot. If I back off the throttle it seems to clear-
  6. puffitu

    Sears Ted Williams 7.5hp

    So I recently acquired this motor and at first glance I see no fuel pump…am I or it missing something?
  7. puffitu

    59’ Evinrude 5.5hp single fuel line conversion

    So I’m converting this model to a single fuel line to eliminate the need for a pressure tank. After watching a few how to vids I think I’ve got it rigged up with a Briggs and Stratton pump, removing the small reed valves and plugging up the right side of the manifold. Any input into start up...
  8. puffitu

    59’ evinrude 5.5hp

    Having a heck of a time putting the water pump assembly back together. When all tightened down; I cannot budge the drive shaft to turn by hand. The specs don’t show any gaskets between wear plate and pump housing and seems extremely hard to turn…any insight ??? Model 5518
  9. puffitu

    6hp 6rl75r

    Anyone got any ideas as to where I can get pistons and rings for this model? Part#s 386692 378432
  10. puffitu

    1970 Johnson 4hp hard to steer

    Maybe a dumb question but I’ve got a couple of 4hp direct drive Johnson’s which I’ve resurrected, but the last thing I’d like to do is to loosen up the rubber which they both swivel or pivot to improve steering. It seems very tight. Normal?Thanks
  11. puffitu

    '84 evinrude 6hp E6RCRM

    Trying to revive this motor. Its showing signs of life after performing some maintenance such as plugs, fuel lines, head gasket, thermo, carb kit, impeller, seals etc. it fired up for about 5minutes and pumped water and so on, then it stalled out. Checked fuel delivery and checked out. Decided...
  12. puffitu

    1970 johnson 4hp

    how difficult is it to set check points on these ?
  13. puffitu

    '95 motorguide GWB52W

    Hello All I would welcome any input on my trolling motor which I recently inherited. I am able to switch to forward; working as should, neutral; working as it should but when switched into reverse; it goes into full blast forward. So no reverse at all. Not a big deal as I can ultimately turn the...
  14. puffitu

    Startup sneeze-1988 125hp

    Hey all Just wanted to hear some input on a slight cold start sneeze I’ve been trying to chase down. It’ll only do it at cold start; seems to clear up after I throw it into high idle
  15. puffitu

    Torque specs

    Hi all I’m trying to resurrect a 1984 evinrude 6hp and in need of torque specs if anyone’s got them.. thanks
  16. puffitu

    ‘60 evinrude 5.5hp carburetor settings( model 5520)

    Hello all Wanted to know a good starting point for setting carb after doing a carb kit; how many turns out on, other adjustments etc?? Thanks in advance
  17. puffitu

    1060 Evinrude fisherman 5.5hp

    Hey all I’ve recently acquired this vintage 5.5hp and after starting to comb through it, I came to a halt after trying to drop the lower unit for inspection. Is there a pin or some trick to release it?? Seems stuck. Thanx
  18. puffitu

    Trim tilt gauge and sender unit install?

    Hi all I’m contemplating installing a trim tilt gauge( which I already have) on an 1988 force 125hp. My question-where should I start looking for a sending unit for this configuration, which is a two wire unit? Thanks
  19. puffitu

    88 force 125hp carb question

    the carb repair kits come with two different looking inlet needles-which one goes to which carb?
  20. puffitu

    Trim and tilt visible leaks

    88 force125hp. Seeing visible leaks from around trim piston and tilt. Ordered the o-rings and going to grab a pin tool and 1/4” socket to get ready to do this. The unit works pretty good aside from having to add fluid before each outing. I’ve read the stickies but just wanted to hear from others...
Top