Search results

  1. P

    FICHT woes

    Hello. I have a 1998 FICHT 115hp that won't Idle. Dies under 1000rpm. Can't find a service manual for that exact year. System voltage is 27v and crank sensor reads 880 ohms. Any ideas or specs? Thanks
  2. P

    How to remove this seal housing?

    Does anyone know how to remove this seal housing from under the waterpump? I need to change the drive shaft seals. 50 hp 4-stroke Thanks :)
  3. P

    How to remove this seal housing?

    Hi Is there a trick to removing this seal housing? I just want to change the driveshaft seals.... 1996 50hp Merc 4-strk Thanks
  4. P

    Old Merc control cables

    Hi Can anyone tell me if Teleflex ( or anyone else) makes replacement cables for a 1967 Merc 350 with dual lever controls? Thanks
  5. P

    1970 40hp evinrude prop

    Hi Gents I have a spun prop from a 40hp big twin. (pin drive brass prop) Can it be rehubed? Are there aftermarket props available? There are no markings on the prop. What was the typical pitch for that size when mounted on a light 14' fibreglass? Thanks :)
  6. P

    can't determine year....

    Hi Gents Please tell me how to find the year of this OB. Its 135hp s# 06110409 (Canada) I've looked everywhere!!
  7. P

    1970 40hp Evin Synch

    Hi Gents, I need your help please....I have a 1970 40052a Evinrude big twin. I can't find in my manuals, how to adjust this secondary pickup adjustment. Thanks in advance!
  8. P

    Load Resistor ohm value?

    Hi Gents Does anyone know the ohmage value of the ignition "load resistor" Thanks in advance
  9. P

    OMC HT400 on threads

    Hi Gents. Anyone know what can be used in place of HT400 on the Timing wheel retainer bolt? Thanks
  10. P

    Iboats search function

    Hi Gents Is it just me, or is the search function for repair forums useless. I tried "VRO" and it comes up empty. What could I be doing wrong? Thanks :(
  11. P

    pressure washer sand blaster attachment

    Hi Gents Just wondering if anyone has had any experience with the add-on sand blaster attachment for a pressure washer. It simply pulls in sand or glass beads at the nozzle.... Thanks Randal
  12. P

    Water pump pressure??

    Hi Gents A few years ago, when my memory was better, there was a website that listed outboard engine water pump pressures. It may have been a gauge manufacturers site. Anybody know where to find such a spec or chart? Thanks
  13. P

    Winterizing Video from NAIT

    http://www.nait.ca/flash_videos/techlife/winterize.html cheers!
  14. P

    1995 50hp spec

    Hi all Still waiting for my manual to come in. Can someone please tell me the recommended operating rpm for this motor. And also, is this the idle speed adjustment in the attachment. Thanks :)
  15. P

    1995 50hp timing

    Hi Gents. I have several manuals, but none for smaller engines. Could someone please give me the specs for timing on a E50DTLEOS 1995 50hp. I need idle timing and max timing. Thanks in advance. :)
  16. P

    Removing heavy scale from water jackets

    Hi gents What methods have you used for removing heavy scale from water jackets and passages? Thanks in advance!
  17. P

    How to size ducting in a new home?

    HI I am installing my own furnace in a modular I have purchased. How does one size or calculate the heat and return air plenims? Thanks
  18. P

    Camcorder disassembly

    Hi Gents<br />Does anyone have any tips on how to disassemble a Canon Optura 10/20?<br /><br />Thanks
  19. P

    Plasma cutters

    Hi Gents<br />Has anyone had any experience with the low cost plasma cutters found on Ebay? Chiry, Mitec, Riland all look tempting, but I'm hesitant.<br /><br />Any comments?<br /><br />Thanks
  20. P

    8mm movie film transferred to DVD

    Anyone need any 8mm movie film transferred to DVD?
Top