The iboats forum moderators are excited to announce that at this time it appears the iboats forums posting pictures function is working once again. Though we cannot promise for how long, we're hoping for indefinitely.
I have an 82 Mercruiser 5.7 with a pre-alpha drive. I am preparing to do the next reseal and in the process, have learned that I may need the following
special tools:
1. Engine alignment tool OEM 91-57797A3
2. Hinge pin removal tool OEM 91-78310
3. Lower shift cable tool OEM 91-12037
4. Shift...
This may be the wrong forum subgroup, but I have a 1982 Sunrunner 245 with a merc 5.7. It has twin saddle fuel tanks and orginally had an electric tank switch solenoid that said " not for marine use ". I replaced it with a manual 3 way valve so I can select either tank or turn off. It is mounted...
I have a 1982 Mercruiser 5.7 MCM 260 serial 6817160. I installed Champion RV91MC plugs, based on the book at West Marine. After noticing the difference in tip length, I removed them and checked for signs of contact and saw nothing.
My Clymer manual shows AC MR43T and my Seloc shows Champion RBL8...
I have a 1982 mercruiser 5.7 . I was checking the compression ( one at a time), but was flooding the carb badly in the process. I would remove the coil cable, remove old plug, checked the compression, gap and installed new plug, then reattached the coil - distributor cable. When attempted a...
I have a 1983 mercruiser 5.7 gm with a pre-alpha drive serial 6817160. I was investigating an oil slick in the bildge. I started the engine and noticed water leaking into the bilge from a small machined hole just above the water inlet neck. It is on the transom assembly straight up above the...
I am planning on replacing my pre-alpha's water impeller. I think the merc part numbers are #46-96148A8 for the Alpha pump kit that supposedly will work on this unit. I read that I should replace the base as well, but that is a pre-alpha specific merc part # 46-5723A1. Does this sound right...
I will be changing the lower unit impeller on my 1982 Mercruiser GM 5.7 with a pre-alpha.
1. Can this be accomplished correctly without removing the outdrive?
2. If I have to R&R the outdrive, must I replace the gasket kit for the outdrive each time? Do I use gasket sealer when I do so?
It is a...
Please confirm that no sealant ( like a gasket or perfect seal ) is required when reinstalling the lower unit back onto the upper gear housing. Just making sure.
thx.
I need to replace the water impellor, so I need the mercruiser part numbers for the kit and the outdive seals when I put it back together.
It is a 1983 Mercruiser 260 /350 with a pre-alpha drive or "R" ( I think ). The top cap has a loop or hole that I suppose was to be used for lifting. The...
This may not be the correct forum, but I use this one a lot.. so I would like to remind everyone about the importance of actually wearing their life preservers. I watched for two days while our local divers worked to recover a gentleman who fell out of his boat and hit his head in the process...
I am running a mercruiser 1983 M260/350 GM with a pre-alpha outdrive in a 1983 Sunrunner 245 cruiser. I replaced a slipping 14 1/2 inch 19 pitch aluminum prop with a Solas Amita 3blade 15.5"x17 pitch aluminum from Iboats.
This boat went from a top end of 23 mph @ 4200 rpm ( GPS ) to 36 mph @...
I am installing magnesium ( freshwater ) anode to my 83 prealpha outdrive. I noticed that aluminum acorn anodes that go on the to lower bolts had gaskets. The new magnesium ones did not come with gaskets.
I am putting a new block anode ( the one that goes over the trim fluid manifold tucked...
I had a problem where the up trim switch was inop, but the down trim & trailering switch worked. The trim limit switch was replaced about 1 1/2 years ago. Thanks to advice from Fishermark & Don S, I check for chaffed wiring and the bullet connectors near the pump. I cleaned those connectors and...
Since ownership, my engine starter operated a bit differently than I expected. When I turn the ignition key, it would turn over fine, briskly & engaged; but wouldn't fire up & actually start the engine until I released the key. Then it would run fine.
A mechanic a couple of years ago said that I...
I had my Merc pre-alpha gearcase resealed about 1 1/2 years ago. But I recently took a close look at the prop shaft oil seal. It is a rubberized seal, but has a visible constricting spring embedded in the rubber material. Most other shaft seals that I have seen, this would be an inner seal and...
My 83 Merc pre-alpha outdrive has suffered significant corrosion in the past 2 years. Much of the problem is caused by my ignorance, I think.
1. I neglected to replace a broken ground cable that goes from part of the steering arm to the inside transom assembly ( about 1 year )
2. When I did my...
This boat is a 1983 Sunrunner 245 with a Merc 5.7/ pre-alpha outdrive. I was running at 4200 r.p.m., no problems. Stopped the boat momentarily, & shifted to nuetral with no problems. When I shift back into forward, there is no engagment. Same with reverse. There is no obvious sign of something...
I am planning a trip from Kemah, TX to Galveston with my Sunrunner 245 ( 350 Merc single ). This will be my first adventure in saltwater. Any advice on navigating, should I stay in the ship channel , obstacle avoidance,
places to visit, Coast Guard interaction,.. etc?
I have a VHF radio, depth...
While replacing the distributor cap on my 83 5.7 GM small block Merc model 260( 6817160 ); I noticed a 90 degree downward fitting that looks like a relief valve or vacuum fitting attached to the lower part of the cap. There has never been a hose attached on it since I've owned this boat. I also...
I am planning to replace my exhaust manifolds & risers on my 83 Merc 260/5.7. My concern is that the boat will need to remain wet in the slip due to a lack of a trailer. If I understand the system, the risers will be above the waterline but the tubes will have water in them at some level. I...