Search results

  1. flashback

    Heat transfer dope

    Does anyone do maintenance on the TB ignition module like replacing the transfer mastic? Since there hard to get maybe some tlc will keep it going a while?
  2. flashback

    Garelick pedestal seat

    Never had a boat with pedestal seats, this one does and they don't seem to have any bearing but just aluminum to aluminum..is there a bushing missing?
  3. flashback

    Radio protection cover

    Now that most of my mechanical issues are repaired I'm looking at little things. Can anyone tell me what the catch is called so I can shop for it?
  4. flashback

    Holt oil extractor

    Recently bought a holt oil extractor mainly for the boat but I haven't used it yet. Any way the change oil light came on in my old 2001 GMC so figured to try the extractor on the truck.. the hose fits in the dipstick tube with room to spare but doesn't get deep enough to reach oil. So I figured...
  5. flashback

    Clear hose

    I've often seen recommendations for a section of clear hose installed at the thermostat for the water intake to diagnose overheating. Can you leave it in the system permanently and if you can, what type or brand?
  6. flashback

    Front wheel bearings and hubs

    I have a 2001 GMC Sierra RWD and the front bearings have been hollering for a few years and need replacement. Doesn't look difficult but deciding what to buy is.. what are your thoughts on the TRQ brand. This old truck has 200,000 miles on it and I can get the said brand almost anywhere..
  7. flashback

    Cooling hose kit

    I need some help with selecting which kit to get. so many different variations to choose from.. If Iboats has one, I'll get it from them, figure the least I can do for all the help I get here.. Thx
  8. flashback

    port side exhaust elbow over heating.

    1995 searay 220 5.7 alpha1 gen 2 with sei drive.. I'm hoping you folks can help me, like the thread title says the port side elbow gets very hot soon after cranking the engine. The riser and the rest of the exhaust system is still cool to touch but that one elbow will almost burn you. The...
  9. flashback

    Clear coat for gel coat

    I'm old school and just got curious.
  10. flashback

    1995 Searay 5.7 GM winterizing mods..

    I just posted a question to Rick Stevens in Cedarcove's thread on the same subject but decided to start my own to avoid confusion. new to me boat so I expected some pit falls. The first was the block drains, they were the little wingnut spigots like they used to put on a radiator in the old...
  11. flashback

    Mystery switches

    I have two toggle switches that energize when the IGN key is on but I have no idea what they are connected to, if they are original or added. The black knob is a dimmer for the gauges. They have wires connected that disappear and I can't find out where they go.
  12. flashback

    Gimbal bearing mystery

    I recently changed the gimbal bearing and being the curious sort I took my old bearing apart. The tolerance ring has a gap in it that aligns with a hole in the carrier which in turn aligns with the grease fitting on the housing. When I removed the bearing from the carrier I found a channel...
  13. flashback

    Is talormade curved windshield really glass?

    They seem to advertise it as glass, but before I try to clean off some paint overspray that it gathered sometime in the past it would be good to know what its made of.
  14. flashback

    Steering maintenance

    I would like to reduce the slop in the steering system so I read up on it in the manual and came across one of the many Merc "IMPORTANT" boxes..."slight feed back could be encountered if cable guide tube flat surfaces are not positioned vertically." Mine are horizontal. I don't know what slight...
  15. flashback

    Prop shopping

    I inherited a 1995 searay 220 with a 5.7 carbed. The prop on It is a black max 14.25X 21p with half a blade missing. Have no idea how it performed when in one piece. I've no need for a fancy SS prop but I would like to get a decent AL and could use some guidance.. Thx
  16. flashback

    Buffing the hull

    This process is not new to me. 30 years ago I buffed many using 3M heavy duty compound with a wool pad, but times change. That said, if there's a better way these days, I'm all ears!
  17. flashback

    Time to reassemble

    Dis -assembly went easy, I just cut every thing made of rubber and thru it away. one of the hinge pins on the ring was hand tight and the other not much better so that was a surprise. anyway I got my new parts and just need to do a bit of cleaning and I am ready to put things back.. Got a...
  18. flashback

    Engine coupler woes

    I removed the gimbal housing today and got a bit deeper, I can't find any splines on the coupler. This boat is becoming more and more discouraging. I suspect I know the answer but just thought I would ask. Can a coupler be swapped while the engine is in the boat? I don't have the equipment or...
  19. flashback

    The leg is off

    After the fourth crowd headed out I was able to get the boat out at leisure yesterday. Fuel pump replacement preformed. Pulled leg and discovered what seems to be a metal plate glued at the top of the transom housing. I'm baffled, why?
  20. flashback

    Wire rope replacement

    I have some fraying and want to replace the 5/16 cable on my lift. I have done this once before but had a few folks to help keep tension on the cables when winding them on the drive pipe. This time I will need to do it by myself and was wondering if any of you folks have a tip for doing it.
Top