Search results

  1. brodie123

    Bell Housing - Merc 250 vs 292

    Hi Everyone. My boat used to have a 165HP L6 250 engine but was toast and tossed. I have a 292 L6 to install and is ready to go 100% except for the bell housing which does not fit - I thought they were supposed to be an exact match. I need to identify what bell housing part # to get. The...
  2. brodie123

    Just curious

    I'm just wondering what symptoms you would see if an engine block was not able to breath properly. I.e. breather cap or other blocked and not allowing gases to vent.
  3. brodie123

    Strange oil pressure

    Mercruiser 4.1L inline 6 What has been done and tested: Water pressure is good - lots of flow New oil pump, filter and oil Cleaned out the Pickup tube Issue: Runs for first hour or so 100% Oil pressure slowly starts to drop Oil press eventually reads very low and then the temp goes up...
  4. brodie123

    Merc Digital to Analog Conversion

    2020 Mercruiser 4.6 V6 250HP We installed this new motor but apparently the motor puts out a digital signal for oil/temp/tach and all our gauges are analog. The motor has a 14 pin connector. Boat has a standard 10 pin. How do we go about getting analog signals? Is it just a different pin...
  5. brodie123

    Johnson 40 HP charging issue

    I have a Johnson 40 HP outboard and I can't find +12 on any wire to charge the battery Model: RDSL-28B Serial: J2684871 I could not identify what wires I should be testing off the schematics I saw. So first question is what wires should I be testing? From there, I can start tracing to the...
  6. brodie123

    Seeking boat storage in Titusville to Daytona area

    Hi everyone. We are seeking boat storage in Titusville to Daytona FL area for our catamaran. I've been calling around but no luck so far. We need storage from July until September. Any suggestions? Thx! Chris
  7. brodie123

    Auto Pilot - Raymarine and Coastal Explorer

    I need some basic assistance to connect my Raymarine P70 auto pilot to my laptop with Coastal Explorer. I have my USB to serial adapter but not sure what else I need. I expect to do some manual wiring which is no problem. Any feedback on that?
  8. brodie123

    Long Trip Home - Florida to Georgian Bay

    Hi everyone. We made the plunge and acquired a 34' Catamaran in Fort Myers Florida and now starts the trip home to Georgian Bay Canada. I've traveled this route with my parents in the past however will be the first time for my wife and I so any additional tips/tricks or even must-see locations...
  9. brodie123

    Switching to AutoPilot controls

    We have a Thompson Daytona 270 with rack/pinon cable steering and we are wanting to add an auto pilot. The part I'm stuck on is the drive controls for the steering. What's the best (and yet economical) way to do this? Is there a hydraulic system that can tie in? Do I have to change the...
  10. brodie123

    Knock Knock - Who's There - Hopefully not a bad piston bearing

    Hi all; Mercruiser 250 L6 4.1L When checking my base timing (6 degrees) which was fine, I dropped the RPM as low as it would go. A knock became evident. Sounds more like a TICK than a knock actually. Brought motor back to ~800 rpm (or less maybe) and the knock went away. I pulled 1 spark...
  11. brodie123

    Harmonic Balancer Install

    Hi All; Mercruiser L6 4.1L My harmonic balancer has spun (the outer rubber) and needs to be replaced. I have a replacement for it. Getting off is not problem. Installing is my concern. With the motor in the boat and the mount removed, I have about maybe a foot of clearance for working. I...
  12. brodie123

    Cedar Boat Stain

    I'm looking for suggestions on what color stain to use on my Peterburough cedar strip that I am stripping down to the plain wood. It appears to be white cedar. I'm looking for what be a common color used for cedar boats. After the stain, I plan to use clear coat urethane. Any...
  13. brodie123

    Mercruiser 250 - won't run

    Hi everyone. I have a Mercruiser 250 4.1L L6 that won't run. I tried to find the serial # but can't find it - the valve cover is not the original I think. (does not have the Mercruiser stickers etc.) It was rebuilt (complete) 3 years ago at a shop. It was a used engine I acquired. I had...
  14. brodie123

    Rectifier Question

    Hi All; We have 2 engines that are both Mercruiser 3.7L L4 engines one of which we just acquired. The original we have has a rectifier and I attached a pic here. The one we just acquired, on the rectifier, does not have the piece of metal going between Point A and B marked on the pic like...
  15. brodie123

    How much should I sell it for?

    Hi all. I have a Merc L4 205 engine in good running condition. The top end was rebuilt a few years back. I'm looking to sell it but do not know what I should be asking for it. Any suggestions???
  16. brodie123

    Rebuild recommendations and options

    Hi everyone; Re: Mercruiser 250 I/O ~1988 L6 4.1L I'm installing a new engine into one of our boats and will be the engine listed above. I will be re-building from scratch and wish to build it in a way as to get as much HP out of it as possible. I already had the engine above in the boat with...
  17. brodie123

    Plastic panel care

    Hi all. Can anyone recommend the best method for cleaning and caring for the plastic panels for our dodger? Everything I do seems to almost make it worse. We have a couple spots where the window has turned to a light brown haze and would like to extend the life of them as long as possible...
  18. brodie123

    Solar Power - Long Term Use

    Hi All. We now have solar panels on our cabin cruiser as we anchor a lot and works fantastic. We typically get 2 amps but often see 4 amps in full sun. We are charging a large 12V deep cycle battery that runs the fridge etc. There is a charge controller that shuts off the charger to avoid...
  19. brodie123

    Suzuki 6hp 4 stroke vibrating

    I have a Suzuki 6hp 4 stroke - approx 3 years old. It seems to be vibrating more than usual. First thing I checked was the prop by not even a scratch. The vibration seems to be coming from the top end. The gas I am using is 87 Octane - about 4 months old. I'm not sure if it's out of warranty...
  20. brodie123

    Missing and no power under load

    Hi All; 2007 Mercruiser 4.3L V6 - Alpha 1 drive - Rebuilt carb - new plugs, dist cap and rotor - new fuel filter - drain and replaced gas with new - compression is good No power under load. Starts fine but rumbles. It appears that 2 cylinders are not firing. 1 of which comes in and out for...
Top