Search results

  1. P

    Need help on 6hp Chrysler

    Got a 6hp Chrysler Model 64H8E S/N 534E. Top cly has no spark set points to .020 still no spark. Is there a way to test coils and condenser. It has two coils numbers on one FWN1038 grey in color the other is FWN 2500 and is black. The look the same except the color. Both coils look good, no...
  2. P

    Need help on year?

    What year would a 30hp Evinrude model E30ECCE S/N R 744379 long shaft, remote be. Looked a number of places and can't seem to find it. Also this motor has a T/T unit on it. It has prestolite SAE J 1171 on a tag, also HYA 110. Need motor for this unit. Any help would be great. Thanks
  3. P

    Were is the pee stream?

    On a 65hp Evinrude model 65273 s/n J o10936 1972 year? Motor starts and runs great in tank (about 10 to 15 minutes) at fast idle motor gets warm, but I can't find any place on motor with temp higher than about 155 f. tested with a temp gun,then temp will drop as if themostate opens which I am...
  4. P

    M W Seaking help

    I have a Montgomery Ward Seaking 6hp Model VWB52006, S/Nn 47X20632. Can any one tell me the year and some history on this motor. Thanks
  5. P

    15 Evinrude Questions ??

    Got a 15hp Evinrude Model E15RCIS (not sure of last two letters may be 1 and a 5). S/N 0003031. Question what year is it? Also is the water pump working OK. Get a slight mist from hole about halve way down back of motor with motor running at fast idle, not in gear and in a tank. Have not had...
  6. P

    65hp Evinrude cooling Question

    Got a 1973 65hp Evinrude remote long shaft. Pumps water fine. Checked by taking cover off thermostat and running motor in tank shot water out poppet value 4ft. Replaced cover but don't see warm water coming out anywhere. Should water exit out rear of motor in middle two holes at rear. Run motor...
  7. P

    1972 25hp johnson L/U oil & seal

    Serial E3605187 model 25R72R put L/u oil in and it leaks some out seating on floor. Did I use wrong oil or should I used some kind of grease (Lubplate 105)? Napa list a seal for this motor (part #18-2005) but the exploded view I have don't show a seal at all on prop shaft just a O-ring. I havn't...
  8. P

    Gamefisher 7.5hp

    I have a Gamefisher 15hp S/N 6028 Model 225581501. Need help, what year is it. Can not find much information on it. Were might I find an exploded view of this motor. Need some information, fuel inlet and primer pump also ignition. Any help or advice would be great. What other motor might...
  9. P

    Evinrude won't go into reverse.

    Buddy has a 1986 Evinrude remote on his pontoon. When on trailer remote is put into forward or neutral or reverse every thing works as it should. don't matter if you check by hand with motor not running or with the motor running with ears on for cooling. But when you put in water it will go into...
  10. P

    Clinton 5.5 help

    Just got a motor for local dealer. I know nothing about motor (it does turn over) dealer said he was told it started but recoil rope was broke. It is a Clinton 5.5 hp model K550 6000A S/N 1586625 What year, what gas mix, what oil or grease is used in l/u. Spark plug # and gap? points? What is...
  11. P

    Bad coil? 7.5 hp sea king

    I have a 7.5hp clinton seaking s/n 1380505 model k751 type KTV50575B, number on base of coil mount is 268-0086-50, that started fine last fall won't start this spring. No spark, is there a way to check coil and electronic box. I'm guessing little white box is electronic ignition(no points). Is...
  12. P

    To much smoke

    I have a 1999 25hp johnson on a pontoon 1/2 open or faster on smoke. Slow down it will smoke. Appears worse at night or when its damp. Put on two new coils and new spark plug wires helped some. Using NKG BR7HS plugs. Will using a hotter plug help? Is it possible to have a leak in the exhaust so...
  13. P

    How many Amp

    I have a 1999 Johnson 25hp el. start. About what is the amp output wide open and at about 1/2 open. Thanks
  14. P

    converting 8hp mercury to remote

    I want to convert a 8hp Mercury long shaft s/n ob103614 I believe about a 1985-1987 model to remote. I don't think the stearing will be a problem. The shifter and fuel control is were I need help. Also help with the el. (picture or diagram). Thanks for any help.
  15. P

    1981 Johnson neutral switch question

    Having problem with the neutral switch on a 25 H.P. el. start. If I understand this switch is to complete the circuit so the solenoid will work but only complete the circuit if the motor is in neutral. My manual states the space between the switch and the cam is 1/16 inch to be measured with a...
  16. P

    Starting 25 H.P. Johnson problems

    Posted yesterday and screwed it up trying again. 25 H.P. Johnson Model J25RCIM (not sure of the I) S/N E5435464 1984 model (I think) With both plugs out motor turns over great. With plugs in it will come up on compression then stop or sometimes will go over and stop on second compression. Both...
  17. P

    Help to change oil in L/U 8 h.p. mercury

    I have a 8 h. p. mercury long shaft S/N ob103614. Need help in oil change. There is a drain plug on skeg like most motors have,but no top plug. There is a stove bolt (about 1/8 inch bolt} just under the water pump. Is this the top plug or does this hold something in place and if I take it out...
  18. P

    Which gas is best

    Read different opinions on proper gas to use in 2-stroke outboards. If mixed at 1/50 with a good oil should you use 87,89 or 91 octane? What about that gas that the octane rating is raised by adding ethaniol at the 10% level good or bad? Will a higher octane smoke less and burn cleaner? What...
  19. P

    25H.P. Johnson smokes whats wrong?

    1999 25 H.P. Johnson on pontoon with T/T run it about level. Will run clean for a while then it will load up and smoke a while. Tryed adjusting carb (adjusting screw on top of carb that sets at an angle) did not make any difference. Was running half open then slower than half open again...
  20. P

    8H.P. Mercury year help!

    Just got a Mercury 8 H.P. long shaft. Set for 3 years. S/n is OB103614 looked on many sites. I can not find it. Also compression both cly. is 80# isn't this low. Motor looks like new and starts on first pull every time including on first start. Runs and shifts exellant. I have decarbed the...
Top