Search results

  1. fisheymikey

    rectifier test

    I just was checking my rectifier and I am puzzled.... when I have the engine not running it has a constant 12.3v that im assuming coming from my battery. when I have the engine running I see it drops from 12.4 to 5 to 6 to 12 to 6 etc... always dropping Is that normal? mike
  2. fisheymikey

    bleed tilt trim force 125

    I want to bleed the oil in the tilt trim I suspect some contamination.... creamy white I did use 30 non detergent oil so want to flush it out I remember some said remove one of the tubes then cycle up and down which one? mike
  3. fisheymikey

    stainless prop force 125

    if ever I get this engine running right... I was wondering if it easy to fing stainless props for a 125 force 1988? mike
  4. fisheymikey

    cylinder 1# and #3

    I am totally stumped all of a sudden cylinder 1&3 not firing I have force 125 1988 any idea maybe just a wiring diagram would help thx mike
  5. fisheymikey

    fuel vent making noise

    force 125 in 18.5 trophy UPDATE! when I put some gas a bunch of water leaked out of the vent what the heck?? I seem to hear a gagleling noise like drinking water there is not that much fuel in it but a weird noise any ideas? mike
  6. fisheymikey

    Splice ignition wire

    I think i found my stuttering /bogging down problem... As trying to figure out my symptoms i checked the spark plug boot and i saw its does not make a solid contact and my rps change when u twist the boot. Even when i applied dielectric grease. Thus my question can i splice the coil wire solder...
  7. fisheymikey

    in gear does not want to move

    force 125 1988 140 on all cylinders all 4 sparks... also if revove any spak plug boot immediate reaction. here is the problem in neutral I could go until 3000rpms in forward gear I go until 2000rpms and a full bogging down action. the only thing out of the ordinary was when I had to shift in...
  8. fisheymikey

    cylinder #4 clean as a whistle

    I have a force 125 1988 on trophy 18.5 I have 140lbs on all cylinders here is the problem, all 3 cylinders above are relatively dirty and the bottom one is very clean. im assuming its due to the engine swap I made in the beginning they have used a silicone gasket. also when I remove spark...
  9. fisheymikey

    cam position force 125 1988

    here are some pics no matter what I do I cant seem to get it right... I listen to the link and sink but getting the screw in the middle of the scribe lines with the buttleflies open is impossible. these pics are the best I can do... what im I doing wrong mike
  10. fisheymikey

    sand in telltale

    I found sand in my telltale and was blocking the flow. I blew it out and now its free of sand and I have flow threw it but....... the flow is half the pressure. my question is do I need to do something to remove the sand somewhere else? do I change the impeller? can I flush out the system thx
  11. fisheymikey

    what the heck is this??

    after an amazing 5 days fishing I had some hesitations issues again. I think I found it but please confirm your theory please thanks
  12. fisheymikey

    force 125 1988 gargles

    well I here we go again... this is the symptom: it gargles at 3500 rpms then clears up and then sometimes runs rough at 4300 I have done the following: installed new see threw filter no bubbles clear installed fuel pump diaphragm changed all connection changed fuel lines primer bulb timing at...
  13. fisheymikey

    static timing

    I have a lot of different statements. can someone clarify please the following... i removed spark plugs and grounded them, removed the propeller, jumped the trigger safety. i want the know the following...there is 3 marks.. from left to right is it 32-30-28 that is what im assuming. if so i...
  14. fisheymikey

    Spark plug boot

    I have a force 125 1988 The boot on cylinder 1&3 have a slight rip at the elbow Even a little bit of grease comes out! Does that cause any issues to the boat... Meaning loss of power etc... Thanks for the help Mike
  15. fisheymikey

    engine stalling,starving,electrical....

    here is the link hope it works force 125 1988. I have a trophy 19 engine noise - YouTube I hope someone has any ideas... please any advice will help I have timed, new conectors compression on all 4 cylinder 141lbs mike
  16. fisheymikey

    i istalled the wrong installed the wrong spark plugs!!!!!

    Re: i istalled the wrong installed the wrong spark plugs!!!!! this fell right off!!!! could this be the culprit??!!! i just cant believe it would be as simple as that it was attach? to the same coil cylinder 4 well i don't have any forks so i need to wait until tomorrow
  17. fisheymikey

    i istalled the wrong installed the wrong spark plugs!!!!!

    Re: i istalled the wrong installed the wrong spark plugs!!!!! ok maybe one of the brand new plugs failed. that's the only thing that make sense. and yes I have the blue coils. I will post later the findings thanks guys!!! btw here are a pic from my fishing trip in cape cod!! I have fish for...
  18. fisheymikey

    i istalled the wrong installed the wrong spark plugs!!!!!

    Re: i istalled the wrong installed the wrong spark plugs!!!!! I adjusting timing because I was not getting the specs... I was off by a lot I need to run the engine and remove immediately? I am running at 4700 at wot 37 mph. I think 13/ 17
  19. fisheymikey

    i istalled the wrong installed the wrong spark plugs!!!!!

    I really hope I did not damage the engine.... I have a 125 force 1988 I installed BUHW instead of BUHX I also timed it accordingly I get around 4700 rpms. after inspection my bottom spark plus seams not to have combustion it looks very clean. am I hurting my engine. I don't have my timing...
  20. fisheymikey

    both carbs leaking

    hi everyone, as you look at the carbs from the boat to the back... top left there is one hole on each and was leaking fuel... what would that be I just rebuilt it and ran awesome. is maybe the floats stuck or needles are finished but they looked fine do I need to open the carbs again please...
Top