Search results

  1. fisheymikey

    force 125 hesitation

    Re: force 125 hesitation well here is the tear down of the exhaust gasket after a good visual. I had a lot of carbon deposit on cylinder. but the gasket is still intact the plate is a bit warped... would the tear be obvious in regards of the gasket? in regards of the comments before...
  2. fisheymikey

    force 125 hesitation

    Re: force 125 hesitation here are some pics as per Jiggs request... I tried both plugs off and plugs in without the one testing. one pic is the plugs after use about 1 hour on the water other is the "the wet test" exept for cylinder 4 it had a very little fuel the others were bone dry...
  3. fisheymikey

    force 125 hesitation

    here my motor ready to go in the water... what do you think the hesitation is? I put timing light on each plug no misfire, float are adjusted with carbs immaculate... transparent fuel filter before carbs full and primer bulb rock hard any ideas?? force 125 hesitation - YouTube thanks
  4. fisheymikey

    compression changed after new headgasket

    I have a 125 1987. I recently changed the head gasket during the winter months. I followed the process of torque, last year I had 141 on all 4 cylinders now im getting 125 on all 4. can my compression gauge be the reason or a weak battery could do that? thanks mike
  5. fisheymikey

    throttle 125 force

    here is throttle end connectors. I did not take a picture before removal. which end goes were? the long one goes to throttle and the short to the gear case? or vise versa thanks mike
  6. fisheymikey

    are all carbs the same

    hi everyone I have 125 1988 I have 2 carbs one has tc-xxxx and the otherone has only numbers. question is are all force 125 from 1983 and up are the same? if not please tell me what to look for thanks mike
  7. fisheymikey

    hds strucute scan

    hi everyone here is a pic of my current setup I need to add my new lss2 ducer... I want to install it were the arrow ends don't know what that gadget is! please let me know your advise were I should put all my ducers thanks mike
  8. fisheymikey

    Vortex prop

    hi I ordered the Vortex prop 15 pitch for my 1988 125 has anyone tried them? are they the same company with Michigan? thanks
  9. fisheymikey

    fuel pump check valve

    hi everyone! just received my check valves... im aware that there is a certain way to install them. I looked at the diagram but does not indicated how. I am also aware one of them is very difficult to get to... any details how to remove would be great thanks mike
  10. fisheymikey

    hds7 gen2 with hds7 touch

    hi everyone! I have done a lot of research with my hds devices. my hdstouch is on its way and I have a question in regards of syncing both unit. what I understand from a prostaffer lowrance. when I connect both devices via Ethernet cable they will both automatically populate all info i.e...
  11. fisheymikey

    flush engine

    force125 1988 I was wondering if there is a way to flush the engine. I have seen calcium build up on other ppl engines and want to do some preventing measures before I have a actual problem. my engine does not over heat so I think its flowing correctly. is there a addictive I could add to the...
  12. fisheymikey

    puddle drain WOW!

    Re: puddle drain WOW! well I screwed up! I think I blew the valves trying to clean them with my air compressor. air flow and carb cleaner can go both ways now and I still cant find the part number for my valves u could see them in brass valve on the puddle drain cover. or is it only a...
  13. fisheymikey

    puddle drain WOW!

    Re: puddle drain WOW! here it is the pics
  14. fisheymikey

    puddle drain WOW!

    here is the puddle drain on my 1988 125 imassuming the black stuff is not part of the gasket. when I rubbed it the black stuff coming apart like fiber material is that normal? can I go ahead and remove all the gasket its pretty stuck on it thanks
  15. fisheymikey

    exhaust gasket torque

    hi I have 125 1988 well Im pretty sure I did not do the right procedure for installing the exhaust gasket. I did the gasket with black gasket maker and never retorque it after initial installation 1st question should I just retorque if so at what poundage? or should I remove the head again and...
  16. fisheymikey

    fuel pump valve

    hi everyone! I have fore 125 1988 I was told on a other thread thad my valve could be bad due to the bottom cylinder #4 is washing clean i.e seam to be leaner than other cylinders. I checked on iboat and to ship to Canada is a whopping 30$ the parts itself is only 11.52. is there a way to...
  17. fisheymikey

    hds 7 gen 2 transducer

    hi everyone! I just was going threw some tutorials in regards my unit and I never set the transducer type I looked all over the place on the transducer and there is no indedification on the cable or the transducer itself.. is there way to figure this out? thanks mike
  18. fisheymikey

    testing my dva meter

    hi everyone! I just finished builing my dva adapter and works great... tested on a few batteries and works!! now I have a few question I did look at the outboard ignition web site and they clearly indicated witch wire to test from.. but the only question is do I do the testing during running? at...
  19. fisheymikey

    powerhead bolts

    hi here are 2 bolts from the bottom severely corroded does that mean my gasket was faulty? thanks mike
  20. fisheymikey

    force 125 carb question

    Re: force 125 carb question here is also the carburetor idle screws I wanted to know the one on the left has a small defect at the tip does that effect anything?
Top