Search results

  1. The Force power

    '87 Force 125HP ignition problem

    That leaves me with one; tested good but no voltage output
  2. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    I'm not sure if I'm getting this right? Does the "earlier LU" have a two piece OR one piece drive-shaft? The one piece came in two lengths 20" & 25" IF the length is correct; it should fit??? Hopefully jerry jerry and/or Nordin will tune in and verify the year(s)
  3. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    Yup, it looks like a hotchpotch The lower-unit a Merc "update" version
  4. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    The "upper pivot bolt" as you refer to, that the the two clamps together rarely come out/apart In the top picture is still a US marine with (maybe) a Merc trim motor & apparently with typical Merc. clamp-down bolts. As for the motor on the boat.....looks to me like the old Chrysler cowl Jerry...
  5. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    IF you have the indeed have what say; then yes you can. I have done this a few times & is not too much work. You'll either have to have both motors laying on the ground or hanging off a host by crank eye-bolt Remove the bottom clamp(two bolds) & you'll see the pivot-shaft. I use an old visegrip...
  6. The Force power

    New to the site with a question about a 1996 90hp Force

    I never seen yellow Teflon-tape for sale here, likely because pipe-dope is to be used here
  7. The Force power

    Throttle and remote control linkage adjustment

    There's ring-groove in the outer-shell of the cable, make sure this aligned/snug fit under the clamp
  8. The Force power

    New to the site with a question about a 1996 90hp Force

    Things change over time & he may of overlooked /not been aware of it
  9. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    You probably went thought / checked this already; NO FIRE OR INTERMITTENT ON ONE CYLINDER: Check stator and trigger resistance, trigger wire sets read approximately 50 ohms between the wire sets (DVA-4V or more), stator reads 680-800 ohms (factory) and 200- 300 (CDI/RAPAIR) DVA 180V or more...
  10. The Force power

    New to the site with a question about a 1996 90hp Force

    I have to in combination with Teflon around the tread, I guess I have same problem as jerry jerry
  11. The Force power

    '87 Force 125HP ignition problem

    Good morning Jiggz, The reading(s) are from one set blue to yellow I checked with a good working one counted the coil-windings (5) each they're (more or less) between the one blue & yellow un-installed / Bench test The two Stators that gave me a reading from one set, I stripped the wiring...
  12. The Force power

    New to the site with a question about a 1996 90hp Force

    IF.....the motor has not ran for a long time; the water mixed-in with the gear-oil WILL separate & sink to the bottom. So its an easy check to see, Just a word of caution; IF there a high percentage of water in the gear-case it can/will freeze (depending on it's location)
  13. The Force power

    New to the site with a question about a 1996 90hp Force

    :D :D I'm with you on this Also most automotive gear oil are not anti-foaming VS the marine LU oil
  14. The Force power

    '87 Force 125HP ignition problem

    So now I have 3 none working Stators; - two stators that don't have reading on one set of the wires - one stator that the readings are good but no fire on 3&4 I guess with the last one I can't do anything, however the first two I'm planning to strip the wires back as close as possible to the...
  15. The Force power

    '87 Force 125HP ignition problem

    Can this be caused by the Stator getting warm/hot resulting in poor flow of current?
  16. The Force power

    '87 Force 125HP ignition problem

    Thanks Nordin for confirming Sometimes I read things too many times & overthink. Why is the OHM-reading for the charging-side not mentioned anywhere?
  17. The Force power

    '87 Force 125HP ignition problem

    WIRE READ TO OEM OHMS Brown/Blue (or Blue) to Brown/Yellow (or Yellow) = 680-900 OHMS is wire below the other brown/blue (or blue wire) or referenced to both? Brown/Blue (or Blue) to Engine GND = Open Brown/Yellow (or Yellow) to Engine GND = Open
  18. The Force power

    88's Gamefisher impeller parts

    You should really read the rules before you post
  19. The Force power

    88's Gamefisher impeller parts

    IBoats sells them!!!
  20. The Force power

    Swapping engines 2004 90hp mercury to a 1989 125 Force wiring

    IF I understand you correctly.... are you just swapping the ignition?? or complete power head?? Either way; Your "Mechanic" has it wrong! up to 1999 Force/Merc. had certain components in common. A 2004 for sure NOT
Top