Search results

  1. The Force power

    Milky fuel in carb intake force 85hp

    Any water in the fuel?
  2. The Force power

    150 hp lower unit replacement

    The right tools & know how but A seal-kit for sure :)
  3. The Force power

    150 hp lower unit replacement

    Where are you located?
  4. The Force power

    How best to close your small business?

    OR.......get better @ cutting hair
  5. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    In addition; I made a habit to install an additional ground-wire from the bracket to the Neg. battery cable-lug
  6. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Yes, the top one is Not the bottom one that for the Merc. ignition system
  7. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Have you trimmed / cut the wires back on the one set with lesser reading to see if the wiring was damaged getting a better reading?
  8. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    I had another look & I see now the second white-green lead, sorry yes it looks like the correct one
  9. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    OR https://www.outboardignition.com/trigger.asp?boatparts=136-4029-4
  10. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    when I searched the # I found , So I think they send the wrong part
  11. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    I would check the Stator-wires that is giving less than 680 ohms
  12. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Where do you see any of the trigger-wires going to ground?
  13. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

  14. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    No readings are taken from the trigger-wires to ground only between the sets (#1/#2/#3/#4) With all the wires still disconnected; take a volt-reading(with a DVA-adapter attached to your meter & meter set to DC volts) (1) from each set of trigger-wires = should around 4.5 volts (2) from each set...
  15. The Force power

    '87 Force 125HP ignition problem

    (1) voltage-test with DVA & meter set to DC (2) I'll take a picture & no I never used since I purchased
  16. The Force power

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    I'm struggling with these issues myself & for myself to simplify this; I disconnected ALL the trigger-wires from the terminal-bar to eliminate any false readings & clarity (1) verify you're taking a reading from the correct trigger-wires (per set) Then disconnect all the Stator-wires (except...
  17. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    As the gear-case where not "labeled" with stamps, the only way to know what you got would be either look for a date stamping in the cast or by counting the revolutions of the drive-shaft v.s. prop-shaft
  18. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    The white plastic adapter is just pressed on the copper-tube (unless someone glued it) DON'T pull the copper P/U-tube out!! Hold the P/U-tube in place & try then by making a twisting motion while pulling on the adapter. IF all fails.........you could break the adapter off the tube so you can...
  19. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    Force went to a 2-piece shaft (on the 85HP & some other) in '88 so they could use the same as the one used on the L-drive units The later version you have came in '91/'9 B model & many other version followed. Believe me when I say; it comes off, I do it every time when I have a motor just...
  20. The Force power

    Can I swap factory tilt/trim from Mercury version 85hp to US Marine version 85?

    The are both Force/US-marine lower-units (there is A later Merc. version(s) that are not compatible)the two you have still are. The white plastic-adapter on the copper P/U-tube will come off & you can slide on the preferred one However the water-pump housing & plate can not be swapped-out
Top