Search results

  1. D

    1988 Starcraft Mariner MR 220 V rebuild

    Opti and...little Baja yellowtail
  2. D

    1988 Starcraft Mariner MR 220 V rebuild

    Oops double post
  3. D

    1988 Starcraft Mariner MR 220 V rebuild

    Some other stuff done..cushions are done...console refurb mocked up...bimini installed...hydraulic lines and control cables run...batteries moved to front of helm seat...Optimax 200 mounted... more to come
  4. D

    1988 Starcraft Mariner MR 220 V rebuild

    Back in action after left knee replacement...looking for ideas. I pulled the center console into the garage to rehab, paint and updates. Need advice on getting it back into the boat. The engine is bolted in place, so its gotta go over the gunwales...???
  5. D

    1988 Starcraft Mariner MR 220 V rebuild

    Any sources or tips for repairing or replacing the vertical transom trims...mine have some corrosion...but sure how you would fabricate a 1-3/4" channel with an almost 90 deg bend???
  6. D

    1988 Starcraft Mariner MR 220 V rebuild

    Got around to building a stand for the Opti 200...needed to get it off the pallet and check k out the forklift damaged port lower cowling...geeze this think looks huge on a stand! Gotta get splashwell finished so we can get the engine mounted on the boat...one step closer to splashing it!!
  7. D

    1988 Starcraft Mariner MR 220 V rebuild

    She has a motor!! 03 Optimax 200..one owner maintenance documentation including controls, harness and smart gage!!!! Yee hah!! Picking up motor next week
  8. D

    1988 Starcraft Mariner MR 220 V rebuild

    Rivet question? Looks like replacing the factory original carpet will be much easier if I remove the rod holder brackets etc....( factory carpet was installed under all these brackets then riveted) Any idea what length rivets these would take? Didnt see them mentioned in the "rivets sticky"
  9. D

    1988 Starcraft Mariner MR 220 V rebuild

    Windy every day has slowed down the foam installation...looks like its gonna take 10-11 sheets...all deck boards are cut, preserved and urethane. Tackled rebuilding trailer bunks...for rid of the old lumber and replaced with polyurethane coated 2x6 (no more carpet)...also added 3/4" HDPE...
  10. D

    1988 Starcraft Mariner MR 220 V rebuild

    Yes...Mariner MR220V always a center console
  11. D

    1988 Starcraft Mariner MR 220 V rebuild

    Need some minor technical help..preparing the put the console and bench seat back in. I forgot to take measurements or pictures of where they were mounted. Would appreciate any help from the Starmada. Thank you in advance...foam and decking this week...nautolex to follow...
  12. D

    1988 Starcraft Mariner MR 220 V rebuild

    Thank you for sending that....
  13. D

    1988 Starcraft Mariner MR 220 V rebuild

    Fyi...what you see is one 4x8 sheet of 1" board...guess it's going to take 3 or 4 total...stay tuned!!
  14. D

    1988 Starcraft Mariner MR 220 V rebuild

    Extruded...not expanded...polystyrene..1" thick..on edge...rigid, closed cell..waterproof..lengthwise..on top of the cross ribs
  15. D

    1988 Starcraft Mariner MR 220 V rebuild

    Thanks
  16. D

    1988 Starcraft Mariner MR 220 V rebuild

    Working on the new deck and foam...delayed by high winds almost daily...and a few dust devils thrown in for good measure...yay!
  17. D

    1988 Starcraft Mariner MR 220 V rebuild

    Thank you!!
  18. D

    1988 Starcraft Mariner MR 220 V rebuild

    Well about 250 rivets later...7 patch panels in...5200 to glue and seal...PC11 2part epoxy inside the hull....new foam tomorrow
  19. D

    1988 Starcraft Mariner MR 220 V rebuild

    New transom is in...transom has been reskinned and patch panels for the hull...rivets on Tuesday!!
  20. D

    1988 Starcraft Mariner MR 220 V rebuild

    YES!... The splashwell may come off as one piece..I didnt know that...I am rebuding mine and will put it back in as one piece. Just finished reskinning the new transom and making patch panels for the hull
Top