Search results

  1. D

    Starting motor not charging

    Why cannot you verify? Again, why unable to verify?
  2. D

    Second mortgage for a carb?

    Holley oem power valves are clearly stamped with a vacuum value and are available for purchase individually from Holley Not uncommon to have issues when tuning a carb to a motor and have a backfire. This ruins the power valve so having a few on hand is a good idea
  3. D

    2 Questions

    In a hard turn the u joints are stressed to the maximum. Probably hearing something related to that. Have you pulled the drives to inspect? Shift cable adjustment is performed at the linkage located on the aft side of the driveshaft housing. Behind the cover. If the trunion is adjusted to be...
  4. D

    Odd shift cable fail

    Will default to post #4 again, however the first statement The updated, thicker, more tensiony v spring is painted yellow on the ends. I'm afraid I cannot explain that any more
  5. D

    1980 3.0L strange overheat issue

    Stuck lifter? Wrong pushrod/spring? Bent rocker? Tuliped valve? Are all the other valves sound and set proper?
  6. D

    Odd shift cable fail

    If you did you wouldn't have posted a situational explanation with no resolve Benefit of the doubt concerning your prowess, the interrupt switch has failed?
  7. D

    Lower shift cable issues alpha 1

    If you're looking for 9/16" end play and seeing 1-2" the inspection you're performing is not correct To go further, if the end play is indeed 1-2" then the installation was incorrect. As in, that cannot happen even if the installation was close but not quite correct Kinda like looking in the...
  8. D

    Volvo Penta 5.0 GXI-E - Won't roll over

    Sounds more like subaru head bolts
  9. D

    Fuel in oil, how many oil changes should I do?

    Yes Change it as many/few times as you like If it were mine I'd change it until the fuel smell goes away You can reuse the filter, or change it. Wondering if febreze in the filter would help with gassy smelly?
  10. D

    Chris craft scorpion wiring diagram

    But..... The wire colors? 888? Ford Not used by mercruiser in 1985 save for the 470 (kind of)
  11. D

    All-Around light pole rake

    If it's 360 the angle less than 20 degrees fore/aft is moot Flashlight and a white plastic drinky cup works in a pinch
  12. D

    Showing the Boston Whaler 13 some TLC . . .

    A testament to OMC. They had the inline two smoker dialed, like really dialed We won't talk about v engines Anyone know why some of these blocks were painted white and others black?
  13. D

    Lower shift cable issues alpha 1

    You are not inspecting the stated specification
  14. D

    Odd shift cable fail

    Post #4, second statement Take the time to witness how the shift plate system works. There's a lot going on there, you can't just glance at it a couple times and figure it out. It's like convoluted simplicity
  15. D

    Odd shift cable fail

    2023 I explained it?
  16. D

    Odd shift cable fail

    There's a v spring update (years ago) with yellow paint on the ends that can help Also, if your shift interrupt switch is the older style, spring arm/roller style the adjustment is a #1 phillips and needle nose
  17. D

    350 Mag Mpi hard to start when warm or hot

    16in at idle is good, yes. Needs to be steady, like less than +/- 1in for minutes If fuel pressure under load is okay with a vacuum drop continously until wot with steady you're good, for now
  18. D

    speedometer pick up tube

    Guessing it's the tree clip speedo tube clamp attached to the forward side of the exhaust passage at the bell housing? If so, no worries. Speedo tube is independent of any water passage save for the pitot at the leading edge of the gearcase
  19. D

    Pulling engine - need help with transmission disconnect

    Looks like you've gone pretty far with a teardown. Might want to remove the entire package and tackle the trans removal on the floor
Top