Search results

  1. b.lee

    Dented pontoon log with tear

    Where you at in Ohio? This might be worth a phone call and possibly a drive up https://detroit.craigslist.org/mcb/for/d/howell-pontoon-tubes-used-garage-sale/7502149549.html
  2. b.lee

    92 Evinrude 25hp questions (e25elens)

    Thanks again racerone! I have yet to find the right diagrams or microfiche for this engine. I was hoping to find some once the top secret sticky thread links are restored.
  3. b.lee

    92 Evinrude 25hp questions (e25elens)

    Anyone with info on the primer lines? Is the splitter stock? If it is stock, then I’m assuming the cut primer line should be reconnected somewhere else on the block or carb?
  4. b.lee

    Just thought I'd share a nice photo.

    Cooke City, Montana
  5. b.lee

    92 Evinrude 25hp questions (e25elens)

    Thanks racerone
  6. b.lee

    92 Evinrude 25hp questions (e25elens)

    Just a few questions about this engine 1992 Evinrude 25hp (e25elens) This hole in the side of the lower unit, I'm guessing this is normal? After running the engine in a trash can I noticed dripping water, what is this for? (I drained the lower end gear oil and it had zero water in it, no metal...
  7. b.lee

    Lower Unit gear oil screws (2 of them) 1991 Johnson 25 HP

    Ran the engine in a trash can full of water today and it shifted perfect, luckily. I was sweating for a bit there. Side note, any marine grade 80w-90 is good for a 92 25hp Evinrude?
  8. b.lee

    Random

    "I must go.... my people need me!"
  9. b.lee

    Top secret sticky

    I just tried to view the winterization link in the top secret sticky and it re-directed me to some sort of Pin issue fix for a Force outboard... argggg
  10. b.lee

    Lower Unit gear oil screws (2 of them) 1991 Johnson 25 HP

    Bringing this one back from the dead, I recently purchased a pontoon with a 1992 25hp Evinrude. Well, I loosened the phillips screw near the flat head drain plug on the lower unit. I loosened it just enough for a little gear lube to drip out, then re-tightened it. It tightened up as normal, no...
  11. b.lee

    I smell a rat.. maybe it's gas..

    I just had a new fuel tank custom built for my 86 Horizon 190... to the tune of $583 (ouch) $515 for the tank, $35 for a new fuel lever sender plus tax ($33) Kehrig makes really nice tanks, that's for sure. The best part is I dropped off the old tank Monday, and picked up the new tank on...
  12. b.lee

    What are these wires for? Trim Gauge?

    Wire #1 goes behind the Trim pump/motor and hooks into the boats wiring harness... Im guessing that's the Trim Up Limit Sensor Wire #2 is just hanging out, I can't find any old mounting locations for it (ones similar to Wire #1's mounting fixed to the back of the hull) ^^^ The end of Wire #2...
  13. b.lee

    More newbie questions...

    This hole, on top of my Alpha 1 Gen 1 outdrive... what is it for? This silver blade or 'fin'... is it supposed to be angled sideways like it is? or should it be facing straight back? Sorry for all the posts... I didn't want to clutter up my other 2 threads. 3rd question.. Can I run my...
  14. b.lee

    1986 5.0L 200HP Mercruiser RPM range?

    What kind of RPM's should I be seeing out of my engine? 1986 Four Winns Brougham 190 5.0L 200HP Mercruiser w/ Mercruiser outdrive Came stock with 14.5x19 3 blade prop, I stuck a 14x19 4 blade prop on it since the original one was a little beat up. I searched and I can't believe there aren't...
  15. b.lee

    What are these wires for? Trim Gauge?

    pic2
  16. b.lee

    What are these wires for? Trim Gauge?

    Pic1
  17. b.lee

    What are these wires for? Trim Gauge?

    1986 Four Winns Brougham 190 5.0L 200HP Mercruiser with Mercruiser outdrive These wires look to be inside a factory oem protective shield. One is black and the other one is brown (I think) My trim gauge is not working on the boat I recently purchased. I'm curious what these wires are for...
Top