Search results

  1. Bondo

    Bravo 3 carrier assembly seal be damaged this way?

    Ayuh,.... Anything, is possible,...... In yer case, I'd say probable,....
  2. Bondo

    1998 mercury 9.9el tracker 2 stroke has no power at full throttle

    Ayuh,....... Welcome Aboard,....... I doubt you need a new carb, muchless a bigger carb,..... What you need to do, is figure out why the fuel system isn't working properly,..... There could be a problem with the tank, the diptube, the anti-siphon valve at the tank's outlet, the gas...
  3. Bondo

    Changing throttle styles

    Ayuh,..... Welcome Aboard,..... If you wish to continue to be apart of our forum, please follow, 'n obey our forum rules,..... The language I edited will not be tolerated,.... There was a change in cable ends a few years ago, so whether you'll need to change the cables, depends on...
  4. Bondo

    No fuel in carb despite several attempts to crank

    Ayuh,...... I'd start by changing the fuel filter, 'n examinin' the contents of the old one for anything but clean fresh gasoline,....
  5. Bondo

    2004 3.0 Exhaust flapper question

    Ayuh,..... That's to high,..... 650/ 700 is where it's gotta be,.....
  6. Bondo

    76 OMC 175 starting

    Ayuh,..... A dirty or corroded connection,....
  7. Bondo

    76 OMC 175 starting

    Ayuh,...... Welcome Aboard,....... No, the points are what causes the coil to fire,......
  8. Bondo

    MerCruiser 5.0 (Carb Engine) will not turn, what is this part?

    Ayuh,..... Welcome Aboard,..... At the keyswitch, with a test light, is there power at the battery terminal,..?? Usually a red wire,... With the key "On", is there power at the ignition terminal,..?? Usually a purple wire,.... With the key to "Start", is there power at the start...
  9. Bondo

    Alternator Belt

    Ayuh,..... As noted above, yer problem is not where yer gettin' yer belts,..... All of mine are from Napa, with no problems,.... Scott lists the most common problem areas,....
  10. Bondo

    Alpha one gen one installing lower out drive

    Ayuh,..... the plastic tube is just to help align the copper tube into the pump cover,..... plastic tube sits on the pump,....
  11. Bondo

    Engine Re-Build - Wire and clearance

    Ayuh,.... Generally speakin', yes,...... There's usually enough room, but rarely to much room,......
  12. Bondo

    Alpha one gen one installing lower out drive

    Ayuh,...... Welcome Aboard,...... I push the copper tube into the upper 1st,..... Then the plastic tube on the lower, helps to guide the two, together,....
  13. Bondo

    1980 120hp

    Ayuh,...... At worse, it might take abit of trimming,..... or not,..... You will need to drill 2 more holes, for the extra 2 mounting studs,.....
  14. Bondo

    Teleflex steering cable source

    Ayuh,....... Buy the helm, 'n cable as a "Kit",...... It's not much more that just the cable, 'n helms wear too,...... 'n if the cables have changed over the years, you'll know it'll fit properly,.....
  15. Bondo

    2009 Tahoe Q5i , prop questions

    Ayuh,..... Welcome Aboard,...... I suggest you stick with an aluminum prop til you get used to bein' a "Boater",...... A prop strike with a stainless prop is more likely to destroy the drive, 'n the prop,....
  16. Bondo

    80's Spartan trailer roller bracket replacement.

    Ayuh,..... Welcome Aboard,...... Never seen one exactly like that, but it would be an easy reman. with some small angle iron, 'n a welder,.....
  17. Bondo

    Smart tabs.

    Ayuh,..... Try it, 'n let us know,.....
  18. Bondo

    Leaking fuel tank

    Ayuh,.... The o-ring seal on the outlet is leaking, no compound is going to change that, you need the o-ring,....
  19. Bondo

    1980 120hp

    Ayuh,....... The Gen.II Alphas came out in '91, so previous to that,...... In 1990, the rear main oil seal changed, so there a possible issue there, unless you get the entire package,( flywheel, coupler, etc),....
Top