Search results

  1. M

    Yamaha 130 2 stroke height

    If the water is nice and flat I can trim up to about 1/2 on the guage but it's rarely flat and calm.
  2. M

    Yamaha 130 2 stroke height

    1997 wellcraft 190ccf center console. 2001 yamaha 130 v4 20 " . Noticed a good deal of porpoising and I can only trim up not even 1/4 ot the trim guage. Also seems like a lot of spray ( whole back of the boat gets wet after running). I can't go back and see where the cav plate is when planing...
  3. M

    Outboard mounting bolts

    I have a 97 wellcraft center console with a yamaha 130 hp outboard. I think I want to raise the motor 1 hole. I mounted it 2 months ago with 4000 silicone and new bolts/nuts. The bottom bolts are in a slotted section on the motor bracket. Think I'll be ok just loosening the nuts (the nuts are...
  4. M

    Evinrude 30 hp compression question

    Nevermind. I put the driveshaft in the crank and tried. Same results. Oh well
  5. M

    Evinrude 30 hp compression question

    Hi working on a 1988 30 hp evinrude 2 stroke 2 cylinder. I forgot to check compression before removing lower unit. Tested and only getting 75 psi on both cylinders. Is there a difference in results if tested with lower unit removed? I know I could just bolt it back on and try it again but just...
  6. M

    Yamaha 130 v4 prop question

    Ok I put a 4 blade aluminum prop on 13.25 x 17 pitch (same as my prior prop but this one has 4 blades) took it out today hoke shot greatly improved planes faster less bow lift coming up on plane. Top rpm was 5400 rpm so I lost about 600 rpm. Previous prop was stainless so maybe that accounts...
  7. M

    Yamaha 704 binnacle remote question

    Ok. Just very important to shut the engine off anytime you move away from the captains seat to minimize someone bumping the control.
  8. M

    Yamaha 704 binnacle remote question

    I'm just being safety conscious. It's never happened. I was just wondering why there is no lock on it.
  9. M

    2001 Yamaha 50hp tlrz 2 stroke with prime start system starts and dies

    I have a oem used cdi box on ebay from a 2000 40 hp 3 cylinder in good working condition Item number 186185638248
  10. M

    Yamaha 704 binnacle remote question

    Anyone know why the 704 remote doesn't have a safety lockout like the 703 where you have to squeeze the button to shift out of neutral? Not talking about throttle only just regular shift and go. Seems dangerous in that if the motor is running and you accidentally bump into the shift lever the...
  11. M

    Yamaha 130 v4 prop question

    Couldn't find my boat in bulletin. Thinking about a 4 blade as my boat needs stern lift due to porpoising issues. Motor is mounted at correct height. From what I researched this hull design is why this happens. My motors rpm range according to the manual is 5500 to 6000. Rated 130 hp is at 5500...
  12. M

    Yamaha 130 v4 prop question

    No. Where should I find those?
  13. M

    Yamaha 130 v4 prop question

    Got my 2001 yamaha 130 v4 2 stroke on my 1997 wellcraft 190ccf center console out on the water today for the first time. Felt a little slow to plane in my opinion. I checked top speed with a GPS speedometer got up to 47 mph at 6000 rpm. My boat only had me on it and 50 gal of fuel in the tank...
  14. M

    Oil fill bezel ??

    Just tried. No dice
  15. M

    Oil fill bezel ??

    Hi I have a 97 wellcraft 190ccf center console. I installed a oil fill tube in the side of my console but it is a little difficult to use as it's mounted flush. I found this picture of almost the same boat but with a angled bezel for oil fill. I tried looking on internet but can't find it ( not...
  16. M

    130 v4 tach question

    I had it connected to the green from the dual fuse guage harness not the 10 pin. When I installed the trim guage I must have unplugged it and then inadvertently plugged it back in to the wrong green.
  17. M

    130 v4 tach question

    Need to delete thus thread. Found the issue I had the green single wire from the tach going to the wrong green in my harnesses
  18. M

    130 v4 tach question

    Hoping someone can help me with what I need. 2001 Yamaha 130 v4 2 stroke. I installed a new old stock multi tach with the round connectors. I have a short adapter to go from round to square from the trim and oil harness. Couldn't get trim to work on gauge so I bought a separate Yamaha trim...
  19. M

    130 v4 oil tank refilling point

    I want to run my 2001 130 v4 on a 6 gallon tank of pre mix fuel before using the main tank in the boat. I placed a mark at the current level in the engine tank (after letting it fill from the on boat sub tank) I want to go through maybe 3 gal of the 6 gal tank and then lift the hood off and see...
Top