Search results

  1. 9

    Marine Sea Foam

    they are in a tournament and need to get to their honey hole before anyone else, and they can fish until the very last and still get to the weigh in station in time
  2. 9

    Marine Sea Foam

    posting your motor model info might help. and it is hard to tell if you really know much about your motor since you think it has carbs
  3. 9

    Marine Sea Foam

    look up Yamaha performance Bulletins for a boat and motor like yours and see what prop, RPMs, and MPH they listed to compare
  4. 9

    2001 200hp HPDI wont run, rebuilt pump, changed all filters, I'm stuck

    did you clean the fuel tank? seems like it ran well until it was put in the water and was moving back and forth. maybe there is some water in tank rolling around since there was rust in the high-pressure pump
  5. 9

    2021 yamaha f200

    easy enough to see if that is what happened just by looking at it. but we have no clule if you have a left or right lower unit
  6. 9

    2021 yamaha f200

    there are a lot of props that will work on a motor, but not work with the hull they are on. and make sure the motor is set at the proper depth
  7. 9

    Excessive Exhaust Steam? or does this look normal?

    I drop the lower unit off, hooked a hose up to the pipe heading up to the power head. hook that hose to a pump sitting in a tub or bucket with the solution in it, pulled the stat out to allow the solution to flow freely thru the motor and turn on the pump. make sure the tell-tale is routed down...
  8. 9

    Excessive Exhaust Steam? or does this look normal?

    if the stat was crusty looking ,I am sure all the passages are too. Rydlime Marine descaler pumped thru does a good job of cleaning it out.
  9. 9

    question on Yamaha ELG 40 carb rebuild

    I agree with Bosco, if it mattered, they would make them to only fit one way or give info on how they need to be installed. And just for the info the fuel flows from the main jet to the idle/pilot jet to limit what both jets dump into the motor at High RPM there should be a rubber plug in the...
  10. 9

    2022 Suzuki rpm issue

    drain the VST to see what comes out of it, maybe clean the screen/filter in the VST also I guess this new of a motor is injected and have a VST
  11. 9

    Yamaha 25hp 2stroke outboard

    timing light hooked up to show you what is really happening with spark timing is the best way to go even if you have to do that with help while running the boat at the point the problem shows up. motor looks like it is jerking around like it has a cylinder not hitting. if you move the timing...
  12. 9

    Yamaha 25hp 2stroke outboard

    compression spark, and timing of that spark are all very easy things to check to see it they are in spec. also, the idle mixture screw should also be where the specs for you motor shows. if it does not run well with all those in spec there is something wrong motor needs more fuel under a load...
  13. 9

    Yamaha 25hp 2stroke outboard

    sounds like there is not enough fuel in the carb bowl to keep up with the usage. possible restriction some where
  14. 9

    Yamaha 25hp 2stroke outboard

    does it help to pump the bulb when the problem shows up. maybe there is an air leak somewhere, so it is not sucking enough liquid fuel to keep up
  15. 9

    1994 250 2 stoke yamaha

    bad check valve on the oil injection system maybe
  16. 9

    Prop Shaft "mid bearing" part number help

    see if you can find a Yamaha performance bulletin for your set up to see what prop they used
  17. 9

    2000 - 200HP OX66 - Fresh Water Flushing Issue

    might try running some Rid Lyme marine descaler thru the system to see if that cleans out the problem
  18. 9

    Prop Shaft "mid bearing" part number help

    I would put a counter rotating prop on it and put the cables back where they were before
  19. 9

    Prop Shaft "mid bearing" part number help

    I was thinking if that is true the thrust bearing is not being loaded up properly when pushing the boat forward. at least that was what i was trying to find out
  20. 9

    Prop Shaft "mid bearing" part number help

    did the prop come with the boat and motor? or did you put a different one on? looking at prop from behind is the prop & shaft turning clockwise when in forward gear or counterclockwise?
Top