That is an ESKA; one of their few water-cooled varieties. It is either rated at 9.9 or 15 HP depending on the carburetor and prhaps some other variables.
One word of caution: :NEVER rope the motor over with the spark plug wires de-tached. The ignition module is VERY sensitive to that and...
Values vary so much depending on your location. Out by me where 2-strokes are banned on many of the lakes......it wouldn't bring much compared to other areas.
Hello all.....
I just acquired a nice Suzuki DT25 S/N
D-13792
I'm intrigued by the ignition; there is no mechanical adjustment of the mag-plate fir timing. No link-n-synch or any of the usual linkages that adjust timing as the throttle is advanced. The twist grip connects with a simple...
Hi,
I would like to have a parts manual for this engine....and specifically I would like to know the part numbers OR THE DIMENSIONS of the upper and lower crankcase seals.
Help anyone?
Thanks!
1960 Scott McCulloch 12HP Model A3FB
Hello....
Today I had the pleasure of going over a Tohatsu 2.5 engine....circa 1983 Model M2.5A 314.
I was all set to replace the fuel lines (this one has the factory fuel pump; no integral tank.
I happened to notice that there is a brass restrictor inserted in the fuel line that runs...
Hello....
Can anyone tell me the procedure for setting the carburetor linkage? I am assuming that the scribe mark on the mag-plate cam is a reference and should mark the spot on the cam that should make first contact with the carb-linkage follower.....but when I set it that way the carburetor...
Hello....
Can someone tell me the typical resistance I should have in the primary and secondary windings of these Prestolite coils?
My coils are original part nuimbers #FWM-1038 (top) and FWM-2500 (bottom).
Also; can anyone explain why there are different part numbers for each of the...
Hello all....
I just acquired a pretty rough Martin 60. In giving it the once-over...I couldn't help but wonder if the lower unit was a TD-20 OMC. It sure looks similar. Anyone know?
Otherwise....any links to Martin stuff would be appreciated. I already have been to the Larson site.....'...
Hello there....
I have the typical three-point puller and the flywheel has the three tapped holes....so all would seem to be well.
However; the way the flywheel is "submersed" into the housing that surrounds it....I see no way to use a strap wrench.
So.....how is it typically done? I...
I just got a 1966 Johnson MQ-12....short shaft. The leg is removed from an un-completed impeller replacement episode. The motor came with this gasket and plastic tube; neither of which looks familiar. I've looked over the parts diagrams and remain puzzled.
Does anyone recognize what they...
ok....thanks for reading.
It's a 1978 Merc 4.5 s/n5071724.
As with most Mercs of this vintage it needs new ignition wiring....and that's what I'm doing.
Question: Underneath the coil...there is a short braided wire that goes nowhere. Should it be grounded? I would assume so.....but it...
Hello all....
I know that there are plans and pictures all over i-boats of engine stands....and cut-away plastic/steel barrels .....but I was hoping to see some examples of combinations that work well.
Here's what I want:
(1) I tinker with older (40's-60's) motors up to....say....35 HP. Some...
Hi...
I have a 1990 Johnson 25 Rope Start. The carburetor has a small screen installed where a welch plug appears on the parts diagram. I have seen this before; I don't question that it's correct for it to be there...but was wondering what it's purpose it.
Here's a link to the diagram of...
Does anyone know where all of his scans have gone? The Webshot links don't work anymore. I've found a few things here and there....but I hope all that all of those wonderful resources are still out there someplace....
Anyone know the current link(s)?
Chuck