iboats - The #1 Store For Everything Boating
 
  #1  
Old September 7th, 2003, 11:28 PM
gemmam gemmam is offline
Cadet
 
Join Date: Sep 2003
Location: Chico, Ca
Posts: 2
Default 40HP Evinrude hole?

66 Sea King w/ 64 Evinrude 40 hp LarkI have an open hole (w/ fitting)in exhaust cover on starboard side near the bottom. Another hole is near the top and has a tube going to carb. Question is what goes in botton hole???Also, where might I find the overheat buzzer/light??? I have found the wire and traced it to the dash.Thanks
Reply With Quote
  #2  
Old September 8th, 2003, 06:13 AM
The Marine Doctor The Marine Doctor is offline
Commander
 
Join Date: Jul 2003
Location: SK Canada
Posts: 2,177
Default Re: 40HP Evinrude hole?

Heat is transfered though a pipe from the exhaust to the carb to release the choke. Works the same as a inboard engine.TMD
Reply With Quote
  #3  
Old September 8th, 2003, 06:22 PM
gemmam gemmam is offline
Cadet
 
Join Date: Sep 2003
Location: Chico, Ca
Posts: 2
Default Re: 40HP Evinrude hole?

Thanks TMD. I understand. But does the bottom hole just remain open to atmosphere with nothing connected to it and not plugged in any way???Thanks again.
Reply With Quote
  #4  
Old September 8th, 2003, 06:33 PM
rodbolt rodbolt is offline
Supreme Mariner
 
Join Date: Sep 2003
Location: Kitty Hawk NC
Posts: 16,798
Default Re: 40HP Evinrude hole?

hello yes the bottom hole allows air in, then the exaust heats the air and intake vacum draws the heated air past a choke coil.the system worked really well for its time but if you desire to tinker with it please get a service manual. read heed and belive.
Reply With Quote
Reply


Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
1998 40hp 4 stoke "weak hole shot" jrpatty Mercury & Mariner Outboards 25 July 23rd, 2006 05:44 PM
'91 40hp Merc Classic...No hole shot or plain out mcdye Mercury & Mariner Outboards 3 July 14th, 2004 02:45 AM
What is this hole for on my Evinrude?!? TrenchFisherman Johnson & Evinrude Outboards 39 August 9th, 2002 08:03 AM
trim hole position on 40hp Tohatsu tiller tenacrewoods Honda & Tohatsu/Nissan Outboards 0 June 25th, 2002 09:27 PM
Mariner 40HP Carb Problems-Pouring Gas Out Hole Wilson Mercury & Mariner Outboards 4 January 21st, 2001 04:50 PM

iboats Forum Directory
Over 100,000 forum posts organized by topic
Outboard Motor Topics
Mercury Outboards
Johnson Outboards
Evinrude Outboards
Force Outboards
Yamaha Outboards
Mariner Outboards
Suzuki Outboards
Honda Outboards
Chrysler Outboards
Tohatsu Outboards
Nissan Outboards
Outboard Motors: non-repair
Vintage Outboards

I/O and Inboard Topics
MerCruiser
OMC I/O, Inboard
Volvo Penta

Propeller Help
Boat Propellers

Boat Repair and Products
Boat Building and Repair
Fiberglass Boat Repair
Marine Electronics
Boat Trailers and Towing
Boat Names
Boat Covers
Boat Parts

Boating Activities Talk
Boating Topics and Questions
Boating Activities and Destinations
Boating Blunders
Boat Shows
Wakeboarding
Water Skiing

Fishing Discussions
Freshwater Fishing
Saltwater Fishing

Boat Type Topics
Aluminum Boats
Bass Boats
Bowrider Boats
Center Console Boats
Cruiser Boats
Cuddy Cabin Boats
Deckboats
Fishing Boats
Fish and Ski Boats
Houseboats
Jet Boats
Jon Boats
Pontoon Boats
Powerboats
PWC Forum
Ski Boats
New Boats
Used Boats

Boat Manufacturers
Boats 250+ Manufacturers
Bayliner Boats
Sea Ray Boats
Zodiac Boats



Outboards

Power Heads

Lower Units

Propellers

Inflatable Boats

Boat Manuals

Engine Parts

All times are GMT -4. The time now is 08:00 PM.