Search results

  1. B

    1996 xr6 150 carb problem?

    runs perfect on the hose of course! cranked in the water, acted a little cold, gave it some throttle and it bogged down, cranks right back, gave more throtlle faster, and she took off like a striped ape! runs perfect at high speed, but falls on its face at idle or a little throttle. thoughts?
  2. B

    Johnson 115 kill switch

    having trouble installing a new kill switch, the attached photo shows my wiring for a 99 johnson 115, i know its the yellow and black wire and then a ground wire (black and white) that i "tap" into, then those 2 wires go to the "M" sides of the kill switch. problem is, when i do all the above it...
  3. B

    water in fuel tank removal

    i have an under deck fuel tank and it has a good bit of water in it. i used the primer bulb to "pump" it out besat it could but still too much water to use. what have you guys done to pump out you tanks? i even considered buying an automotive fuel pump and suck it out, concerned about safety...
  4. B

    1998 erude 115 carb question

    See attached pic of one of my carbs, below the jet is a needle, is that high speed needle? do i need to back it out and clean inside it also? cleaned carbs/needle seat etc then saw this. upon reassembly thanks
  5. B

    1993 evinrude 150 cutting off at WOT

    from idle to 5000 rpm runs perfect, put my foot into it for WOT and she cuts off, cranks right back up, runs perfect until WOT again. what the heck!!!!????
  6. B

    2004 merc 150 xr6 NO SPARK

    fixed the oiling problem, now i have no spark, what the heck!!! ALL 4 YELLOW STATOR WIRES CHECK .000 ohms grn/white and wht/grrn check out at .410 ohms, thast low right? bad stator? do not have a kill switch
  7. B

    2004 merc 150 xr6 warning horn

    with just the key on not running, getting a continuous beep, it used to do one beep then i coud start it oil reservoir is full did not try to start
  8. B

    1999 erude 150 ficht over rev in neutral

    in neutral this thing is screaming!!! , its not the TPS, nor is it the fuel pump diaphram and the plugs have been indexed! any other ideas? thanks
  9. B

    4 pole kill switch wiring OMC

    1999 johnson 115 new kill switch has 4 poles - 2 say "M" other 2 say "I" which wires from control box/key switch go where? thanks
  10. B

    1999 Evinrude 150 ficht high idle

    my motor is idling WAYYY too high in neutral, (so high i dare not shift into gear) hot foot is in correct postion, nothing seems to be binding, or holding throttle open. do these motors have a throttle position sensor? if so where is it located and could that be the problem? thanks
  11. B

    johnson 115 year model

    it seems the "introduces" reference doesnt apply to this one! model VJ115TLATS serial G03161974 what year is it? thanks
  12. B

    Merc xr6 150 year model

    SERIAL NUMBER IS 0D097246, I cant find the year model anywhere assuming its a 1993 but cant find it on any charts online
  13. B

    2004 merc xr6 150 not peeing

    cranked it up, strong stream, drove a lap or 2 warning horn went off, checked stream, still strong, idled back to dock lost all stream. dropped foot impeller looks fine, not chewed up etc, pulled one thermo and it moves like it should, nothing obstructing the intake either, what the heck?????
  14. B

    1969 evinrude 9-1/2 weak fire

    Evinrude model 9722M (1969 model) top cylinder is firing but very weak, bottom cylinder has a strong fire, i have installed new points and condensors, set points at .020 as flywheel states. all screws are tight. then i will either have a weak spark or no spark on top cylinder. two questions. 1)...
  15. B

    1974 Johnson 40hp will not kill

    you guys helped me out on this couple of months ago and i found the problem and fixed it! but now its doing the exact same thing, wont kill with the key switch. new switch ohms out ok, blue and blu white ohm out ok up to master plug, after master plug they ohm to all zeros when the key is on...
  16. B

    1967 Evinrude 9.5 tiller handle parts needed

    model number = 9722M serial number = E01058 low profile 9.5hp need tiller handle parts and have not been able to locate anyone that offers them. any ideas? thanks
  17. B

    1974 Johnson model 40E-74S kill switch wiring

    which wires do i "tap" into to connect a kill switch?
  18. B

    72 johnson 20hp recoil problem

    my recoil will not connect to the flywheel so i ordered new spring and starter pawl, still no luck so i took it apart. see pics. what makes the starter spindle open and close the pawl? how does that work as i see nothing wrong with the parts. i do see an arrow on top of the spindle where is it...
  19. B

    1974 Johnson model 40E-74S wiring diagram

    i am in need of the wiring diagram for the ignition switch, wiring harness has 5 wires: blue, blue/white, purple/white (choke),yellow or tan and red. motor will start with key switch but will not kill when i turn it off. wiring or bad ignition switch?
  20. B

    74 Johnson model 40E-74S 40hp kill switch wiring

    need to add a kill switch, cannot figure out the wires to connect it to. ignition switch has red, white, blue, blue/white stripe, thats is all. which wire can i use for a kill switch? thanks
Top