Search results

  1. catfishr1

    Post a pic of your starcraft!

    The SS means it is a Super Sport.
  2. catfishr1

    Changing my boat gauges.

    Yahoo, all my gauges are working except trim, which has not worked since I have owned boat. Still have some tidying up to do. Trim gauge has 4 volts on sending wire, according to manual need 5 to 7. PO had put new trim pump in, it works but not oe. On the pre alpa outdrives, sender in hydraulic...
  3. catfishr1

    Changing my boat gauges.

    Thank you so very much. Read thru instructions, think have one problem solved with voltmeter, think it may affect tach too. Will post more after test theory.
  4. catfishr1

    Changing my boat gauges.

    Think am closing in on it. Am so very appreciative and thankful for all the help.
  5. catfishr1

    Changing my boat gauges.

    All dodge, you asked who manufacturered the old gauges. Took a picture of old tach, and old voltmeter. Noticed some strange differences between old and new. Think problem is in new tach the way it is wired compared to old.
  6. catfishr1

    Changing my boat gauges.

    Already checked on that. It is a mercruiser motor.
  7. catfishr1

    Changing my boat gauges.

    New thought on ground jumper wire. Hooked it to new volt gauge, switched on all instrument lights came on, had 12.5 volts all gauges. Fuel gauge and temp. gauge was working not the tach? Moved jumper to fuel gauge 12.5 all instruments. Had a storm brewing did not get to test what was working.
  8. catfishr1

    Changing my boat gauges.

    I am fairly sure you are right. Guess need to bite the bullet and install correct dizzy. Am certain you are right about cheap.
  9. catfishr1

    Changing my boat gauges.

    Found out when p.o. installed HEI distributor he must have done away with 10 pin conector. Took a couple pics. to show.
  10. catfishr1

    Changing my boat gauges.

    Traced down wire to horn. That means end on gauge should be on ign. I think?
  11. catfishr1

    Changing my boat gauges.

    I definitely agree on status of wire connectors.
  12. catfishr1

    Changing my boat gauges.

    Sorry, got sidetracked on yellow wire. Have not been able to figure were it's origin is. Will try again to figure out.
  13. catfishr1

    Changing my boat gauges.

    Ran a jumper from battery neg. to meter. Got 12.4 volts fuel, trim, temperature, & voltage. Tach 10.5, speedometer 10.5. Fuel and temp. gauges peg full right when power switched on.
  14. catfishr1

    Changing my boat gauges.

    Will definitely give this a try.
  15. catfishr1

    Changing my boat gauges.

    Yes, old gauges were working except trim. Fuel worked fine 1st year, started acting up close of season last year. Would read full or empty all the time. The old tach, temp, and volt worked great until started changing gauges.
  16. catfishr1

    Changing my boat gauges.

    Have checked readings several times, definitely 2.6 on all but tach. Have tach set on 6cyl 3p. Going to hook up my timing light to make sure getting accurate reading.
  17. catfishr1

    Changing my boat gauges.

    I got good readings today. Ign. on 2.6 volts fuel, trim, water temp, voltmeter, 6 volts tach. Running 9volts tach, 4 on rest. The engine starts right away, every time.
  18. catfishr1

    Changing my boat gauges.

    Got my new multimeter today. Going out now to get readings. Did notice yesterday tach works as long as revs. about 900 or more. Does that mean got a short?
  19. catfishr1

    Changing my boat gauges.

    Will do.
  20. catfishr1

    Changing my boat gauges.

    I should probably mention trim gauge did not work when I purchased boat. Blower quit last year, however was able to hook it directly to battery. Now won't work at all. And fuel gauge been acting weird.
Top