Search results

  1. C

    1988 Johnson 70 VRO Tach not working

    Boat has ran great until a few days ago. Tach stopped working. The engine is charging the battery but I have no signal at the tach. When I turn the key on the gauge zeros and has a good ground and positive feed. I have checked on the block and connected the yellow/gray with the gray and still no...
  2. C

    Mercury High Five on 30ft Party Hut Pontoon?

    I currently have a 2005 Sun Tracker Party Hut pontoon 30ft with a 115hp efi four stroke. The 4 stroke does fine but is very slow. Cruise is around 10mph. It has a 3 blade prop maxing out around 4600 rpm wot. I am thinking of increasing the pitch but going to a 5 blade mercury high five ss. The...
  3. C

    2005 Mercury 115hp Four Stroke EFI Not Charging, No Voltage output

    Went to the boat yesterday. Both batteries are brand new and remain on trickle chragers. Started the boat up and idled it. I could see the voltage dopping on the meter. I also reved the engine to 1,700 rms which dropped the meter more. The engine has only been run a few times since last summer...
  4. C

    Sun tracker party hut 28 enclosures/bimini top

    Re: Sun tracker party hut 28 enclosures/bimini top I sent them an email. The front enclosures are not really a big concern of mine. During boating season it is too hot to stay on the boat without ac and too many mosquitos. Mainly interested in the rear enclosure, if we don't end up putting the...
  5. C

    Sun tracker party hut 28 enclosures/bimini top

    I just bought an 97 Sun Tracker Party Hut 28ft. The rear enclosure is gone and i am looking to get a new one along with the front roll down wall panels to match. Does anyone know where i can get these things. I have tried looking all over but have had no lukc finding them. I know they have to be...
  6. C

    5.7L MERCRUISER SERPINTINE BELT REPLACEMENT DELCO vs MANDO

    Does anyone know what the difference is? I can see that they are different part numbers but what is the difference. The pulleys are the same size. I have the mando alternator but bought the belt of the delco. I am an hour away from the belt and i have a test run this afternoon for a potential...
  7. C

    97 Force 120 Limp Mode

    Looking at a 97 Force 120 that went into limp mode. The engine will crank and run but not go over 2200rpm. Engine did not over heat. The owner has removed the oil system and premixes. Any ideas as to what could be the problem and solution? And possible cost to fix?
  8. C

    97 Evinrude 150 electrical questions

    Does the engine have an external computer. The owner gave me what looks like a main engine harness but he claims that this needs to be installed. But from what i am looking at it already is. What is missing from my perspective is he starting harness. What exactly goes from the console to the...
  9. C

    Which under water lights?

    Looking for the brightest and highest quality under water lights. What is everyone running
  10. C

    What is a 1980 25ft Mako Center Console w/ HPDI 250 Yamaha worth?

    Re: What is a 1980 25ft Mako Center Console w/ HPDI 250 Yamaha worth? Here is a picture. The boat will have a fresh gel coat before it gets sold by a marine shop. The engine is now out of the deal. Trailer is new. I have got him down to $6000. What do you think? He just had the inside repainted...
  11. C

    What is a 1980 25ft Mako Center Console w/ HPDI 250 Yamaha worth?

    Boat interior has just been redone. Boat has T-Top, New Aluminum I Beam trailer, hydraulic steering, leaning post , and HPDI Yamaha 250. The boat does need to be re gel but what will it be worth with a fresh gel coat and a great running engine?
  12. C

    Avenger owners have you ever seen this one?

    I am looking at this boat but i can not tell whether it is actually an avenger boat or if it is a Marauder Marine Avenger. What do yall know?
  13. C

    1988 Concept Marine CONCEPT 21 CTR CONSOLE? Anyone recognize?

    The guy is selling an 1988 Concept Marine Center Console 21ft. Boat has a ~98-2000 Yamaha 150 Salt Series. No problems other than the gel has oxidized pretty good. Comes with depth finder and fm/am/cd/ipod radio. T-Top with new canvas. What is it worth? Its more of a bay boat than a offshore...
  14. C

    Anyone heard of Avenger Boats?

    Re: Anyone heard of Avenger Boats?
  15. C

    Most fuel efficient 2 stroke

    Looking into buying a 225, 250, or 275. It's going on a 23ft center console. The boat currently has a ficht motor and is running great but before any problems occur I would rather upgrade. Which one will burn the least besides a four stroke. Looking mainly at Yamaha because of their reliability...
  16. C

    77 MAko 23ft

    The previous owner painted the tan floor (as it came from the factory) with just an average marine paint with a roller and only one coat. So as you can imagine is it coming up. What i would like to do is to sand down what he has half assed and start over. The floor does need a few patches (screw...
  17. C

    1977 Mako 23ft Center Console

    I gave up on the Avenger. i cant get the guy to work with me at all on the price. I am now looking at a 1977 Mako 23ft Center Console. From what the owner is telling me the boat is made with absolutely no wood. It has a 70 gallon alum. tank in the rear and an added a 40 gallon tank in the...
  18. C

    Anyone heard of Avenger Boats?

    I am looking at buying a 23ft center console Avenger. It looks alot like the scarab. The owner thinks that the boats use to be made around New Oreans La, but they stop manf. after Katrina. Anyone have one? Heard of them? Are they any good? I you do have one or seen them what are they worth.
  19. C

    2001 EdgeRunner 23' Center Console. Whats it worth???

    The boat is a 2001 Fairly good condition. The gel is glossy, engine runs well, only electronics is a radio. It is outfitted with a 200 Johnson. With it in good running condition and sitting on a dual axle aluminum I beam trailer what is it worth? This is obviously the best time to buy or maybe...
  20. C

    1996 VIP Vindicator 21ft with 5.7L Mercruiser

    I am also looking at this boat. The engine runs fine but the gimble needs to be replaced. I had this done about 2 years ago on the same engine and drive package with a mechanic and it was 650 with all parts and labor and he installed new shift cable and all of the boots. So i am not too worried...
Top