Search results

  1. okditch

    1993 90 hp EVINRUDE V4 CHARGING PROBLEM BATTERY DRAINS !!

    motor will start and run with enough voltage...12.2+v,but seems not to be charging (fish finder voltmeter shows only batt. voltage when it used to show 13.5+-v).LOAD TESTED BATTERY OK. I took off neg batt. lead to motor tested (with key off) amps on black multi lead to the cable and red to...
  2. okditch

    Charging issues?!? Load test?

    My 90hp 1993(E90TLETS)EVINRUDE will run ,but appears not to be charging. I tested battery and they said it was good (interstate batt).charges to about 12.8v,but after awhile at sea the battery drops to about 12.2-v and motor wont turn. i got rectifier but havent installed yet.How likely is it...
  3. okditch

    no model tag on motor

    ive realized that my suzuki 15 hp has no model tag.I believe its a dt15c but ,Im not sure what year.How can I determine without a serial number or model number? Thanks:)
  4. okditch

    how many volts to turn over a 93 90hp evinrude v4?

    how many volts to turn over said motor? my fishfinder diagnostic said 12.2v but that wasnt enough to kick the starter over.12.4v has done it in the past anyone know? THANKS..
  5. okditch

    should 1993 90hp evinrude be tickety?

    Hi ,this motor is fairly new to me, but at low speeds sounds a little "tickety".Is this normal?sounds good at high speed though,no real performance issues other than idle maybe could be a bit higher.stalls occasionally when i accelerate out of neutral. Thanks, I like to hear from people that...
  6. okditch

    can you run 1993 90hp evinrude without the thrust pin?

    Re: can you run 1993 90hp evinrude without the thrust pin? I would like do this because its way more motor than the boat needs . its back heavy with a bit of porpoising and bow rise.I almost have it under control in the holes closest to boat, but I feel a little more would be better. the boat...
  7. okditch

    can you run 1993 90hp evinrude without the thrust pin?

    :confused::confused:Can you remove the thrust pin on motor bracket in order to achieve more negative trim,or does it need to be there?I need to get my bow down a little more.Does any one know?thanks:cool:
  8. okditch

    does 93 90hp evirude v4 recharge the battery?I see no alternator.

    As I was saying in the tiltle,can anyone explain how or if this motor charges the battery or not? I know it may sound stupid, but the motor is new to me and i was just wondering...Thanks for any input!-okditch
  9. okditch

    90s 15hp Suzuki Oil Inj Disabled!!??

    HI the kicker I have had the oil injection disabled by the previous owner. I have heard that you should not run straight mix in suzukis and disable the oil besause zukes inject some of the oil to the bearings-- is this true for all years or only certain years? Or am i misinformed? thanks for...
  10. okditch

    Tilt And Trim Maintenance 93v4 Crossflow 90hp

    HI again! Got my motor hoisted.I want to take off the tilt assembly so i can deal with the corrosion. It seems that if i remove the two pivot rods ,and the steering tube,the unit is free. The question is how do i deal with the electric umbilical that connects it? It appears as if its connected...
  11. okditch

    How Much Consumption On V4 93 90hp Crossflow?

    I just got this motor and I am already afraid of how much fuel I might burn.I already know 9gph @ WOT but what is the best I can expect if I drive conservative? Such as trolling or cruising?:rolleyes:
  12. okditch

    treating rust on tilt/trim

    Hi, whats a good way of treating the rust on my 93 v4 90hp tilt/trim? the aft side is clean, while the other side has rust and large paint peels that havent fallen off yet.Any good suggestions would be appreciated! Thanks for the time!!:confused:
  13. okditch

    hoisting 93 90hp v4 crossflow?? ??

    Hi does anyone know a good way of hoisting my v4? its very heavy and hasnt been installed yet.I need to treat some rust issues on the boat side of the tilt/trim system, but there is no hook on these motors. someone said i may be able to hoist using a 3 jaw fly wheel puller is this the best way...
  14. okditch

    what compression on 1993 v4 90 hp?

    any one know acceptable compression on 90hp 1993 v4?:confused:
  15. okditch

    1993 90hp v4 evinrude questions

    Hi everyone I just bought this motor off of craigslist. The guy said it was a 1993 v4 (evinrude), I think I believe nim, but where do I find the model #? I also noticed that the steering pivot is quite rusty. Is this replacable should i be concerned? thank you:redface:
Top