Re: What's involved in swapping 305 ford w/cobra sx to chevy
The motors are complete, so it looks like he will only need bellhousing and coupler... He is in Miami so I am sure he will have no trouble finding what he needs.
Good news, thanks for the help.
I am selling 2 PCM 350/310 closed water cooled engines and a guy has just asked me what would be involved to put these in his boat that had for 302's hooked up to his Cobra sx outdrives.
I have never had an I/O so what should I advise him?
Thanks
I have read some good advice in the forum on repairing my zodiac. I have a lower seam that has come loose, about 4", and i was able to pull it back to about a total of 14" seperated.
Question is, when using the MET to clean it, do I have to clean it down to bare pvc? I have cleaned it and...
Just got a great little boat at a great price. She has sat for about a year. The gas smelled a little bad but not terrible.
After changing out the gas and bleeding the gas lines and carb she started right up. Idles great. Revs up about 200 rpms fine, after that it coughs and stops if you try...
Just installed two new PCM motors in my Carver.
We put a ton of effort into deturmining which was standard and which was reverse but are not 100% sure of the outcome. We marched firing order from the old engines and have the trannys on the same side that they were removed from. Should be right...
I have just replaced my two 305/220 crusaders with two 350/350 PCM crate engines.
They both have an external oil and transmission fluid cooler (heat exchangers) that are not part of the engine hosing, my old engines had just oil coolers and they were inline on the motor.
The only logical place...
I am replacing my motors in my Carver and when I removed the transmissions I saw that the starbord transmission has about 3/4" travel before engaging. By that I mean by turning the shaft on the rear of the tranny it will turn 3/4" either way freely. The other is tight, only a tiny amont of...
I have two mortors and need to keep one and sell one.
One is a 2001 150 Yamaha. 120-125 compression in each cylinder. Runs my 20' Wellcraft up to 45mph no problem.
The other is a 2002 OX66 Saltwater Series II 150. Starts and runs great but so far havn't been able to get her over 4600rpm/32mph...
I just bought a 22ft Angler w/ 150 Yamaha Saltwater Series II Fuel Injected OX66
Boat was a lightly used rental at a high dollar resort.
Starts and runs great. I have not checked compression yet, but have no reason to believe it will be a problem.
I have a 15 x 17 Yamaha Prop on her and she...
Re: Need wiring diagram or part number for speed lcd marine meter!
Here are my wires. What you have helps, but I am not sure it is the same gauge.
I have Black and Blue coming out of one side. I think that is dash lights.
Then I have male Black, Black, Red, Yellow
Which I assume are...
I have been on the web for two days trying to find the wiring diagram for this. I have a 2002 OX66 150 and the guy said this would work but there are wires that don't match mine...
Thanks for any help!
Sorry for the fuzzy photo...
I am searching for the answer, it has to be here, but....
What needs to take place to remove the lower unit on my 1987 Force 50? The bolts came out like new, she seperated about 1/4 inch and now I want to be sure of what to do next.
Thanks
I have found an almost new Force 50. Still has the original plugs (blue) and compression is like new. Everything looks great.
Problem was starter would not turn over, new relay and problem fixed.
Now I am getting no spark.
I am getting 12.54 volts to the blue wires that go to the coils with...
