Recent content by GrindKore

  1. GrindKore

    2005 Mercruiser 5.0 - Hard To Start When Warmed UP!

    Hi guys my 2005 Mercruiser 5.0 TKS (carb 220HP) has recently developed a problem. When cold it starts up right away although at idle speed it tends to run rough with engine rpm varying between 800-600 rpm. When advancing throttle it hesitates but quickly recovers and is able to reach WOT @4800...
  2. GrindKore

    baylinerownersclub not approving new members

    Does anyone here have a forum account at baylinerownersclub.org? Few weeks ago I registered an account there as I had some questions about soon to be ours Bayliner boat, however their moderator must approve new members in order to post or view attachments. I have e-mailed the moderator there...
  3. GrindKore

    Bottom Paint

    We are considering on keeping new to us 2005 Bayliner 242 Classic in the marina for the season. The boat will be in fresh water on Lake Erie entire summer season. Being a trailer sailor I do not have much experience with issues that arise as result of hull and out-drive remaining in water for 4...
  4. GrindKore

    Spitzer Lakeside Marina - Lorain, Ohio

    We are considering leasing a slip at Spitzer Lake side marina at Lorain harbor for our new Bayliner 242 Classic. I'm familiar with the waters there as we have launched our trailer boat for the last 3 seasons nearby and like the proximity to the Islands and Cleveland. We have visited number of...
  5. GrindKore

    Runaway boat - rare footage

    Check out this clip http://www.liveleak.com/view?i=3e5_1269142330 This looks like Boston Whaler, shame a cutoff lanyard would have prevented this mess. Good thing it did not hit other boats or damaged property.
  6. GrindKore

    Argh.. Ruined a new prop today!!!

    Well, I did a number on my prop today. Went out with kids late afternoon, nice calm day got to the launch lane undid my straps, removed transom saver, and waited for traffic to clear behind me. As I started backing down the ramp, about 5 ft from the water I hear nasty grinding sound and in the...
  7. GrindKore

    Trigger Loose? can only get 3200 RPM WOT- Video included, need your advice.

    Hi guys, I have been trying to figure out why this motor (1990 Force 90) will not rev up more than 3200RPM at WOT for some time now. Checked everything I can think of; Spark Tester ? Good spark on all 3 cylinders Spark plugs ? Good condition, not too dirty and not too clean Compression ? 120s...
  8. GrindKore

    Aluminum Prop Repair & Pitch Change.

    Hi Guys/Gals. I have my old 13x19 Michigan Wheel 3 blade aluminum prop that I no longer use. It has few dings and scratches, however it is still usable as a "backup". Recently I wanted to try 17p prop, so instead of buying new one I was thinking on sending my old prop to get repaired and...
  9. GrindKore

    Need feedback on NAUTIC/OSHEN OUTBOARD MOTORS

    Does anyone own one of these? http://www.nauticmotors.com/Nautic_2-2.5-3.html These motors sell under many different brands around the globe, however they appear to be all manufactured in China by OSHEN Industry Group Inc. http://www.oshenmoto.com/. Here is what appears to be a factory demo...
  10. GrindKore

    Force Rectifier On the Cheap - less than $3.00 total cost - Video Demonstration

    Demonstration of RadioShack 25A rectifier working on 1990 Force 90 hp outboard motor. This rectifier cost $2.85 at the local RadioShack store, however it works just as well as the $40.00 replacement marine rectifier for this motor. Video 1 of 3 http://www.youtube.com/watch?v=pAV14aj_DT0 Video...
  11. GrindKore

    Fixing transom holes - - need advice

    Hi guys/gals, I want to remove swim platform from my boat transom, however this will leave three 1/2" size holes below the waterline in my transom from the bolts that were holding up this platform. My first instinct it to use wooden dowels coated with a healthy layer of 3M 5200 marine...
  12. GrindKore

    Flywheel Puller

    Hi guys, what kind of flywheel puller do I need to remove the flywheel from my 1990 FORCE 90? Also, where can I buy one.
  13. GrindKore

    JetFlea Stunt Goes Wrong

    Check this out: http://www.liveleak.com/view?i=acc_1217446165
  14. GrindKore

    Low compression on #1 Cylinder (Updated 7/30/08 w/Pics)

    I just did a compression test on my 1990 FORCE 90 and got following readouts: Cylinder #1 (top): 56psi Cylinder #2: 127psi Cylinder #3: 125psi The thing is, this motor starts easy, idles well, and gives me descent WOT speed (about 34MPH). The only reason I started poking around with...
  15. GrindKore

    How to safely test spark plugs.

    This may be a dumb question, but how do you guys test spark plugs while avoiding fuel vapors that are shooting out of the cylinders? Even after disconnecting fuel line, there is enough gas in carbs and power-head to cause explosion or burns if its ignited.
See more
Top