Recent content by fishing pole

  1. F

    14 HP SPL Evinrude

    Hi, I 've got a 1986 14 HP SPL and it's not running too good. Had not ran it in a year. Once I ran the motor after a year it ran fine at home. Then second time I ran this motor I had to pull the choke all the way out for the motor to run. As the motor was running on the lake I shot some Gum Out...
  2. F

    Motor Running Rich

    Hey, How bad is it for a small 14 HP motor to run alittle rich? Was told that the black looking oil leaking down my lower unit was from my motor running rich. To fix the rich running motor which way should I turn the rich lean screw? All I have is screw driver slot to turn,thats covered by a...
  3. F

    Lower Unit Capacity

    Hey Rick The 14 Evinrude modle is VE14RCCS made in 1988. Thanks Hey, Today first thing I did was drain the lower unit. The lower unit oil looked fine,not milky. I did pour the old lower unit oil into a old clean empty oil bottle. The old oil that came out made the 6 OZ.mark on the bottle...
  4. F

    Lower Unit Capacity

    Hey, Today first thing I did was drain the lower unit. The lower unit oil looked fine,not milky. I did pour the old lower unit oil into a old clean empty oil bottle. The old oil that came out of my lower unit, made the 6 OZ.mark on the bottle. Note: How much does a small 14 /15 HP Evinrude...
  5. F

    Loew unit Capacity

    Hey, Today first thing I did was drain the lower unit. The lower unit oil looked fine,not milky. I did pour the old lower unit oil into a old clean empty oil bottle. The old oil that came out made the 6 OZ.mark on the bottle. It's sort of a one of a kind motor made way back in 1988. I got it...
  6. F

    Gear Lube

    Hey,<br />WHat do ya'll guys think of the Wal Mart cheeper gear lube?<br />I did a lot of trolling.And at the boat ramp white foamy oil was comming out the small holes on the lower unit.<br />No water was in the lower unit gears,I drain the Wal Mart gear lube.<br />I now have the higher price...
  7. F

    Two Small Holes with foamy Oil

    Hey,<br />I just replaced my impller on my 14 SPL 1987 model.<br />I used Permatex on both gaskets. And I put some Permex around the lower unit,where the lower unit fits to the motor.<br />On my second fishing trip,at the boat ramp.<br />I had white foamy oil comming out the two small holes on...
  8. F

    New Impeller

    Hey,<br />This may sound strange.<br />I just put in my first impeller,on my 14 SPL Evinrude.<br />And now I was just thinking should I stay close to the boat ramp.Could the impeller that I put in<br />just stop working for some reason.<br />I just ran the motor in a barrel,for about 5...
  9. F

    Water Pump

    Hey,<br />Thanks Everyone for the help''''''''<br />Well this was my first impeller job on my 14 Evinrude.And when I fired up the motor, water started comming out the water pump indicator.<br /> Great Forum and lots of help. :D Thanks
  10. F

    Impeller Key

    Hey<br />I just put a impeller in my 14 SPL Evinrude.<br />Man getting the key in, took some time.<br />Now I've got the impeller housing bolted down.<br />Hopefully the key didn't come off the shaft.<br />The housing bolted down ok.<br />Could the key somehow sliped out,and still bolt down to...
  11. F

    Lower Unit

    Hi,<br />I haven't started working on the impeller job,yet.<br />Just reading up on the work to be done.<br />On my 1988 Evinrude 14 SPL Mod No. VE14RCCS,<br />How do I get the lower Unit off from the motor?<br /><br />The where's the shift rod connector at?<br />On a older motor there was a...
  12. F

    First Impeller job

    First Impeller job Hi everyone <br />This is my first impeller repair.<br />I've got a 1988 Evinrude 14SPL Mod.VE14RCCS.<br />My water pump indicator stop working.<br />Water will still comes out the exhaust.<br />Can a person do the impeller replacement,<br />without a vise?<br />This is the...
See more
Top