I have an idea in my head but need some answers or opinions from the experts. I know UHMW or HighFax as we call it around here is almost indestructible. Shoot depending on which grade a person is using things such as machining can even be done to it. My question is is there a resin or adhesive...
I ain't freakin out lol but I do have my dunce cap on as I ask this. While cutting out the inner layer of glass to obtain room to remove all the rotten wood from the transom on my Laser I went to deep and penetated the outter skin and gelcoat. It is right in the middle of the built in jackplate...
I need to get some more supplies as in resin and gelcoat and was wondering what any of you have found to be the least expensive place to purchase. Alot of the places that I have bought before charge a good bit for shipping and I know this is due to the hazmat shipping charges. Most of the time I...
I am considering buying a reman Powerhead for one of my motors. My question is this. On the 112 cross flow motor they have listed with bubble back exhaust does the reman Powerhead in fact have the bubble back on it? And if so is the exhaust chest cut like the 140' s.
I have to replace the main hydraulic ram on my trim unit due to an unfortunate accident. My question is ......with the correct spanner wrench is this a pretty well pull it out and replace with new seals? I already have the donor trim unit and need a bit of guidance before snatching it apart.
Ok let me say this before I get to my point of this post. There are several of the oldtimers here that if they tell you a mouse can pull a boxcar u better hookem up. I am NOT challenging anyones knowledge.... I am trying to gain knowledge
Time and time again I see a recommendation for an...
Ok its a 6hp evinrude....model number is 6202DJ06847. My question or questions is what year is this animal so I order correct fuel pump. Also what would be the best way to set the mixture screw after I do the needed repairs. Finally found the crack in the fuel pump plastic piece.
Everything was right then the tach dropped out. Did the normal chech chech and rechech all connections from battery throughout engine harness. No good....but while testing if i had done anygood noticed voltage while running was over 16 volts
Please keep on mind I am a carb motor man and havent...
I am in the process of replacing a broken mounting bracket on this motor. While tearing down I found the main rod in the hydraulic trim system was actually bent at the topside. The used unit I purchased has a good hydraulic unit but bad trim motor. My question is this.....they are both fasttrac...
Is this possible even with the slight 1" difference in case height. Visually that's all I see unless there are internal differences such as driveshaft or shift shaft length am I correct in assuming this is a direct bolt on interchange
I am helping a friend on his 15hp 4stroke outboard. Due to the fantastic fuel we have nowadays (sarcastic humor) lol his carb is pretty gummed up. I have pulled the carb apart and found what I had figured I would find. I have the carb soaking as we speak and my question is....as far as the...
Hello all..I have a question on replacing a defective part on the above mentioned motor. Unfortunately I have to replace the swivel bracket due to an unexpected meeting with a stump. My question is I have looked over the bracket and it seems that once I remove the lower unit and attached the...
Unfortunately I have to replace the swivel bracket and tilt tube,steering arm on this motor. I dont know if there was a stress crack that finally reared its ugly head or the tilt bracket as it re-entered the motor mount had enough slack in it that it actually hung up. The swivel bracket broke...
My tach took a dump and I have ordered a new one. I guess oldtimers is kicking in...i can't remember the pole setting. Could someone refresh my memory.
Ok folks gotta ? fer someone that can help out. Originally my tidecraft didnt have a tach. So I got the needed tach harness. Well in the mean time the reg/rectifier went out. So I had to get one. Installed it and put in a new tach. Visually inspected the stator while the flywheel was off. No bad...
