• If this is your first visit to the iboats.com Boating Forums, be sure to check out the FAQ. To post a question or comment, begin by signing up. To start viewing messages, select the forum that you want to visit from the selection below.


Announcement

Announcement Module
Collapse

Help Tip: If you have a question that has not been answered to your satisfaction in the archives, it is always best to start a new thread of your own. By starting your own thread, you will receive the maximum number of views by forum members.

Below are some additional forum policies in hopes of all iboats members will follow, Thank you.

1. Please do not reply to old topics or hijack existing topics. Old topics of a technical nature are like a library book, Please do not write in them.

2. Old topics should be considered archives and used for reference only. Please do not reply to them.

3. Do not take over someone elseís topic (aka hijack) with your own question, even if it is similar. If you have a question that has not been covered to your satisfaction in the archives, it is always best to start a new topic of your own.

4. If you have a question for the original poster (OP) and the topic is over 30 days old, send the OP a PM, he may not even visit the forums any longer, or may not notice your question in the old topic.

5. By starting your own topic, you will receive the maximum number of views by forum helpers that may not even notice your question when itís posted at the end of someone elseís topic. And those answers will be specific to your particular issue.

6. Please do not post to topics that have been inactive for more than 3 months unless you are the original poster. We have very active forums and any topic that remains inactive for that long should be considered "dead". It is especially confusing when there is an entirely new question posted to an old topic.

7. Posting at the end of any topic is considered to be hijacking the original posters topic which in turn subjects the topic to be closed if it continues to happen thus not making it fair to the original poster in the future had for some reason he/she needed to return for additional information or provide an update of the problem solved which is always welcomed within a reasonable amount of time frame.

8. Please note that you should see a red banner pop up near the bottom of each inactive topic asking you not to reply to old topics. The Red banner will read: Please note this topic has been inactive for 90 days. For the best results, please start a new topic.

Thank you all in advance for doing your part in helping iboats run a smooth ship.

Additional forum rules linked below.
http://forums.iboats.com/forum-rules-guidelines-405/
See more
See less

Yamaha lower unit tools

Page Title Module
Move Remove Collapse
X
Conversation Detail Module
Collapse
  • Filter
  • Time
  • Show
Clear All
new posts


  • Yamaha lower unit tools

    I would like to change the lower unit oil seals on my 1999 Yamaha S130TLRX. The dealer sold me a shop manual which I read and bought the parts, lubes, & sealants. When I asked for tools, they said they do not sell them to the public. I saw another thread that confirmed that but no recommendation on an alternate source? Any suggestions? I need a ring nut wrench YB-34447 / 90890-06511, ring nut extension 90890-06513, propeller shaft housing puller YB-06207 / 90890-06502 and universal puller YB-06117thanks


  • #2
    Re: Yamaha lower unit tools

    And you're willing to spend several hundred dollars on tools that you may only use once? If the dealer doesn't want to order them for you, you may be out of luck. Also they're not something you're gonna get over nite. May take up to six weeks to get some of the tools. Most tool builders build to order not to stock.

    Comment



    • #3
      Re: Yamaha lower unit tools

      Capt Ken:Yes, I am willing to spend hundredes of dollars, it's a hobby. I used to club race Porsches and rebuild engines, now I'm into boating, I just like to be hands on, do you know where I would order the tools? My next option is to hire an independent to train me and have them show me the tools and order me a set, I love working on engines. Spent the last week gettin' the 20 year old Honda motorcycle in shape and the 3 sizes of outboards I own, before that it was the Yanmar 2GM20F deisel in the sailboat needed injectors and a mixing elbo.....the Yamaha 130 is next on the list! please help if you can!

      Comment



      • #4
        Re: Yamaha lower unit tools

        Pcola: Go to www.boatsetup.comFind your way to the Yamaha section and ask Ray or Tony for help.They know Yammies like no other people.John

        Comment

        Working...
        X