1976 Evinrude 85HP - Pee Hole - Tell Tale - Installed

[Royale With Cheese]

I have recently purchased a 1976 Evinrude 85HP and I hooked the muffs up to it to run it.
I fired it up and it was running, but it wasn't peeing.
So I shut it down.
I looked all around, but i could not find a pee hole.

I looked at another engine (1976 Johnson 135) and looks almost identical, but is has a pee hole in the base at the rear.

Am I not looking in the right location?
Thanks for your help.

 

[tashasdaddy]

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Re: 1976 Evinrude 85HP - Pee hole, where is it?

it does not have one. it has exhaust relief ports on the back of the leg, at idle you should get droplets and mist out of these ports. one can be added fairly easily. http://forums.iboats.com/showthread.php?t=222677

 

[daselbee]

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Yeah but pork chops are gooood, bacon is gooood....

 

[daselbee]

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Or how about..."Zed's dead, baby, Zed's dead...."

 

[Royale With Cheese]

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Thanks tashasdaddy
I'll put this in my to do list

 

[Royale With Cheese]

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Part 1
Well I finally got around to adding the tell tale on my 1976 Evinrude 85 HP engine.

Here are some pics.

My engine did not have the bung as in the pictures shown in iwombat's post

Here is the hole I drilled and tapped at the top of the block next to the #1 cylinder.

I used a 1/8 NPT brass nipple instead of the right angle OEM outlet elbow.

Before adding the bulk head hole.

The bulk head hole that I drilled. I did not have a 11/16 drill bit so I drilled the biggest hole that I could and then used a rat tail file to make space for the bulk head fitting to fit into place.

 

[Royale With Cheese]

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Re: 1976 Evinrude 85HP - Pee hole, where is it?

Part 2

Bulk head fitting installed.

Installation complete.

Motor peeing. Success! Woo Hoo!

Thanks iboats and all forum posters.
I couldn't have done it without your help.

Fab

 

[Royale With Cheese]

Re: 1976 Evinrude 85HP - Pee Hole - Tell Tale - Installed

I have had a few people email me about this.
I did it just as reassurance that the water pump was working vs. waiting until the Temperature horn went off.

Being pretty mechanically inclined it was rather easy to install.
Please let me know if you have any questions.
Thanks,
Royale With Cheese

 

[iwombat]

Re: 1976 Evinrude 85HP - Pee Hole - Tell Tale - Installed

I've been meaning to add this little warning to the FAQ . . .

If that's a salt water motor, you definitely want to use the OEM plastic fitting and not the bronze fitting. You'll get electrolysis between the two metals and eventual failure. In fresh water, I don't think it's that much of an issue.

 

[JesterGrin_1]

Very Nice Job I have to say. But then again I am also brand new to Outboards. But I hope not for too long.

 

[GA_Boater]

Five year old post. Please let it sleep. Thanks.