HP55 Chrysler outboard throttle problems

Badhog50

Cadet
Joined
Aug 9, 2015
Messages
24
Outboard idles and runs Placed it in the water and it will run great at low speeds but when I open it up the trottle it dogs out and just speeds up little bit Need advice on how I can fix this problem
 

Attachments

  • photo228212.jpg
    photo228212.jpg
    69.6 KB · Views: 0
  • photo228213.jpg
    photo228213.jpg
    77.1 KB · Views: 0
  • photo228215.jpg
    photo228215.jpg
    78.4 KB · Views: 0

flyingscott

Fleet Admiral
Joined
Apr 8, 2014
Messages
7,989
Try pumping the primer on the gas line while this is happening see if it picks up if it does usually a fuel pump issue.
 

jerryjerry05

Supreme Mariner
Joined
May 7, 2008
Messages
17,926
Compression and spark test, first.
​Then: fuel lines replace, squeezie replace, the inline fuel hose connector remove/replace(the seal rots from age/ethanol).
Then: tank vent make sure it's open, built in tank, the vent hose can get clogged with bugs.
Then: clean the carb, the high speed jet might be clogged.
Then: rebuild the pump.
Install a filter between the pump and carb. Fram G-2/ 3/ 12 one will work.
 

wickware

Lieutenant
Joined
Jun 20, 2009
Messages
1,286
1. When was the last time it ran good at top speed with no hesitation or Etc?
2. Have you put a timing light on it to see if the timing is advancing when you accelerate?
3. When is the last time you checked the points or added points, plugs and condensers?
4. I have the same plugs, points and condensers since 1985 but checked them when sluggish. I had Dirty points vs burnt from adding too much oil to the point?s oil wic.
5. A clear filter between the fuel tank and pump verified I had good gas coming to the pump. A filter between pump and carb could verify fuel. No problems with my original stretched looking diaphragm.

Good Luck!
 

Attachments

  • 70 Chrysler 35 HP Fuel Pump's Diaphragm   Checked Last In 1985 2.JPG
    70 Chrysler 35 HP Fuel Pump's Diaphragm Checked Last In 1985 2.JPG
    48.8 KB · Views: 0

wickware

Lieutenant
Joined
Jun 20, 2009
Messages
1,286
I am told that my one Carb 35 HP is the same as your 55 HP with one Cab and short Lower Unit Leg vs Short Leg. I have a 55 HP Hood on my 35 HP. Feeling too bad to fish after working to the 03 Date.

1. Marked the flywheel to try and check the timing, seeing advance was objective vs ck timing with a gauge.
2. Pulling the flywheel to ck points can be a Bear w/o heavy tools. Re-torque at 90 ft lbs vs shearing a key.
 

Attachments

  • Boat 70 Chrysler 35 HP Flywheel Puller 2.jpg
    Boat 70 Chrysler 35 HP Flywheel Puller 2.jpg
    86.8 KB · Views: 0
  • 2010 Cleaning Since 1985, as needed Greasing (1).JPG
    2010 Cleaning Since 1985, as needed Greasing (1).JPG
    90.6 KB · Views: 0
  • 1970, 35 HP Chrysler's Magneto System 2.JPG
    1970, 35 HP Chrysler's Magneto System 2.JPG
    83.7 KB · Views: 0
  • Boat 70 Chrysler 35 HP Flywheel Holder.jpg
    Boat 70 Chrysler 35 HP Flywheel Holder.jpg
    92.9 KB · Views: 0
  • Lights Added 3 In. Higher.JPG
    Lights Added 3 In. Higher.JPG
    57.1 KB · Views: 0

Badhog50

Cadet
Joined
Aug 9, 2015
Messages
24
Thank you for all this advice! Tomorrow will start checking all of this
Let you guys know
Appreciate this greatly
 

wickware

Lieutenant
Joined
Jun 20, 2009
Messages
1,286
Please edit one Carb 35 HP is the same as your 55 HP with one Carb and ?Long Lower Unit Leg vs Short Leg?. Your one Carb should make our engines compatible except for piston size and Etc to piston.
 
Top